MAX8543EEE+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-SSOP (0.154, 3.90mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Terminal Pitch | 0.635mm |
| Base Part Number | MAX8543 |
| Function | Step-Down |
| Number of Outputs | 1 |
| Output Voltage | 11.88V |
| Output Type | Transistor Driver |
| Input Voltage-Nom | 13.2V |
| Analog IC - Other Type | SWITCHING CONTROLLER |
| Output Configuration | Positive |
| Output Current | 25A |
| Voltage - Supply (Vcc/Vdd) | 3V~13.2V |
| Control Features | Current Limit, Enable, Power Good, Soft Start |
| Input Voltage (Min) | 3V |
| Topology | Buck |
| Control Mode | CURRENT-MODE |
| Frequency - Switching | 800kHz~1.2MHz |
| Control Technique | PULSE WIDTH MODULATION |
| Synchronous Rectifier | Yes |
| Switcher Configuration | PUSH-PULL |
| Max Frequency | 1.2MHz |
| Length | 4.89mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX8543EEE+T Overview
Capsuled in the 16-SSOP (0.154, 3.90mm Width) package, the switching controller can be used for a wide range of applications. dc motor controller is suitable for 1 output generation. PMIC packaging is solid with a Tape & Reel (TR) enclosure. Transistor Driver dc switching's outputs (s) are supported. dc control's supply and operating voltages are 3V~13.2V. Worked in a -40°C~85°C TA dc switcher before. In this switching controller, the switch can be set to 800kHz~1.2MHz. The Surface Mount value makes it suitable for general dc dc regulator. For efficient switching control, the dcdc regulator features Current Limit, Enable, Power Good, Soft Start. An analog IC SWITCHING CONTROLLER is connected to the switch converters. Switching converters are designed with the terminal (s) at position DUAL . An array of 16 terminations of dc switching. These dc dc converter ics adapt several control methods, including PULSE WIDTH MODULATION. The nominal DC switcher's voltage input is 13.2V. MAX8543 can be used to locate other relevant dc to dc converter ics. 16 pins are present on switching converter. The minimum input voltage of the dc dc voltage regulator should be 3V. DC regulator outputs 11.88V voltage according to the test statistics. normally, the dc dc regulator's output current is 25A, which you should keep in mind when starting a project. In most applications and prototype designs, DC switcher is qualified as a Surface Mount. There is a maximum frequency of 1.2MHz on this dc regulators.
MAX8543EEE+T Features
Transistor Driver Outputs
Switching Frequency: 800kHz~1.2MHz
Current Limit, Enable, Power Good, Soft Start
PULSE WIDTH MODULATION
MAX8543EEE+T Applications
There are a lot of Maxim Integrated MAX8543EEE+T DC to DC converter applications.
- Computed tomography (CT)
- Current source circuits
- Domestic water pumps
- Communication system
- Overvoltage protection circuits in TV sets
- Lathes
- Constant current circuits
- Precision electronic equipment
- Machining centers
- Experimental setup
