MAX892LEUA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 1997 |
| JESD-609 Code | e3 |
| Feature | Status Flag |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Terminal Pitch | 0.65mm |
| Base Part Number | MAX892 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 250mA |
| Operating Supply Voltage | 5.5V |
| Interface | On/Off |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Control Mode | CURRENT-MODE |
| Max Input Voltage | 5.5V |
| Control Technique | PULSE WIDTH MODULATION |
| Supply Current-Max (Isup) | 0.05mA |
| Switcher Configuration | BUCK |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Adjustable), Over Temperature |
| Rds On (Typ) | 250m Ω |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX892LEUA+T Overview
It is package in Tape & Reel (TR) case.There is a 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) package that includes it.The LED driver is mounted as Surface Mount.There is a switch type of General Purpose.To ensure reliable operation, set the temperature to -40°C~85°C TA.The LED driver has a total of 1 outputs.A supply voltage of Not Required is required for it to operate.The maximum output voltage of this LED driver is P-Channel volts.In terms of features, the LED driving board has Status Flag.I believe it belongs to the MAX892 family.A total of 8 terminations have been found in it.In order to operate, the 8 pins are used.The LED driver has 1 functions.Maximum output current falls to 250mA when operation criteria are met.In this case, it is mounted in the way of Surface Mount.A total of 8 pins are included in this LED driver.This gadget uses an analog IC, which is SWITCHING REGULATOR in this case.Optimal efficiency requires a voltage of 5.5V.The maximum input voltage of the LED driver is 5.5V volts.As a minimum input voltage, it requires 2.7V volts.In order to operate at its maximum capacity, the supply current must not exceed 0.05mA.
MAX892LEUA+T Features
MAX892LEUA+T Applications
There are a lot of Maxim Integrated MAX892LEUA+T Power Switches ICs applications.
- Notebook and Tablet Computers
- Set-Top Boxes
- Telecom and Network Systems
- Storage Drives
- Hot-Swap Systems
- Low Voltage I/O System Power
- PC Card Hot Swap
- USB3.1 Power Delivery
- Solid-State Drives
- Wearable Devices
