MAX893LESA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 1999 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 70mOhm |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 471mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Base Part Number | MAX893 |
| Pin Count | 8 |
| Number of Outputs | 1 |
| Output Type | P-Channel |
| Max Output Current | 1.8A |
| Input Voltage-Nom | 3V |
| Interface | On/Off |
| Analog IC - Other Type | SWITCHING REGULATOR |
| Nominal Supply Current | 13μA |
| Output Configuration | High Side |
| Voltage - Supply (Vcc/Vdd) | Not Required |
| Input Type | Non-Inverting |
| Turn On Delay Time | 200 μs |
| Switch Type | General Purpose |
| Min Input Voltage | 2.7V |
| Control Mode | CURRENT-MODE |
| Max Input Voltage | 5.5V |
| Output Current per Channel | 1.2A |
| Nominal Input Voltage | 5.5V |
| Turn-Off Delay Time | 4 μs |
| Switcher Configuration | SINGLE |
| Ratio - Input:Output | 1:1 |
| Voltage - Load | 2.7V~5.5V |
| Fault Protection | Current Limiting (Adjustable), Over Temperature |
| Rds On (Typ) | 70m Ω |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX893LESA+ Overview
It is packaged in the form of a Tube.This package is included in 8-SOIC (0.154, 3.90mm Width).This lighting drivere has a mounting type of Surface Mount.The switch type of this switch is General Purpose.It is recommended that the temperature be set to -40°C~85°C TA for reliable performance.The LED driver is equipped with 1 outputs.A voltage of Not Required is used to power it.Voltage output is P-Channel volts at maximum.It is a member of the MAX893 family.A total of 8 terminations can be found in it.The 8 pins are used for the operation of the system.It has 1 functions.In order to meet the operation criteria, the maximum output current drops to 1.8A.As a result, it is mounted in the manner of Surface Mount.A total of 8 pins are included in this LED driver.Lighting drivers with 70mOhm resistance are used.In this lighting driver, SWITCHING REGULATOR is the analog IC.This LED driver can handle voltages up to 5.5V volts.There is a minimum input voltage of 2.7V volts for this LED driver.
MAX893LESA+ Features
Resistance of 70mOhm
MAX893LESA+ Applications
There are a lot of Maxim Integrated MAX893LESA+ Power Switches ICs applications.
- Storage (HDDs, SSDs)
- Portable/Handheld Devices
- Handheld Devices
- USB Power Distribution
- Portable GPS
- Solid-State Drives
- Wearable Devices
- Low Voltage I/O System Power
- Storage Drives
- PC Card Hot Swap
