MAX9016AEKA+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Package / Case | SOT-23 |
| Number of Pins | 8 |
| Packaging | Strip |
| Published | 2010 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Matte Tin (Sn) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Comparators |
| Max Power Dissipation | 727mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Pin Count | 8 |
| Output Type | OPEN-DRAIN |
| Power Supplies | 5V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Nominal Supply Current | 1.7μA |
| Output Current | 50mA |
| Max Supply Current | 1.7μA |
| Propagation Delay | 31 μs |
| Quiescent Current | 2μA |
| Response Time | 31000 ns |
| Amplifier Type | COMPARATOR |
| Common Mode Rejection Ratio | 80 dB |
| Input Offset Voltage (Vos) | 5mV |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Max Input Current | 1nA |
| Input Bias Current | 1nA |
| Hysteresis | 4 mV |
| Height | 1.3mm |
| Length | 3mm |
| Width | 1.75mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX9016AEKA+T Overview
In order to facilitate transportation, it is packaged in SOT-23 .Output type OPEN-DRAIN is used for this comparator.This chip is designed with the Strip package.As you can see, the comparator has8 terminals.The electrical component here belongs to the Comparators family.When supplied with 5V voltage, the comparator is capable of performing a wide range of tasks.The device contains 8 pins.The comparator has 8 pins.In this comparator, the quiescent current is 2μA .There is a Surface Mount for mounting it on a PCB or other board.Electronic comparator is recommended that the nominal supply current of the device be 1.7μA .If the current supply exceeds 1.7μA , the comparator could malfunction.Electronic comparator is sufficient to run the device wElectronic comparatorh 5V power supplies.You can input a maximum current of 1nA into this device.Keeping the temperature below 85°C is not recommended.Comparator electronics cannot be used at a temperature below -40°C .A comparator's maximum supply voltage is 5.5V .This comparator allows minimum supply voltage of 1.8V .As a result, 1 channels work together to maintain the quality of the output.Comparators have a very high gain COMPARATOR amplifier.
MAX9016AEKA+T Features
OPEN-DRAIN output capability
Quiescent Current: 2μA
COMPARATOR amplifier
MAX9016AEKA+T Applications
There are a lot of Maxim Integrated MAX9016AEKA+T linear comparators applications.
- Point of load regulators
- Set Top Boxes
- Power Supervision
- Battery-Powered Electronics
- General Purpose Low Voltage Applications
- Handheld Instruments
- Battery-Powered Electronics
- Consumer Medical Electronics
- Analog front end
- System control and monitoring
