MAX9120ESA
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2007 |
| Series | Beyond-the-Rails™ |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | General Purpose |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | Comparators |
| Max Power Dissipation | 200mW |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Base Part Number | MAX9120 |
| Pin Count | 5 |
| Output Type | CMOS, Open-Drain, Rail-to-Rail, TTL |
| Number of Elements | 1 |
| Power Supplies | 2/5V |
| Nominal Supply Current | 800nA |
| Max Supply Current | 800nA |
| Voltage - Supply, Single/Dual (±) | 1.6V~5.5V |
| Input Offset Voltage (Vos) | 5mV |
| Input Bias Current | 1nA |
| Current - Quiescent (Max) | 1.2μA |
| Voltage - Input Offset (Max) | 5mV @ 5V |
| Current - Input Bias (Max) | 0.001μA @ 5V |
| Hysteresis | 4mV |
| CMRR, PSRR (Typ) | 66.02dB CMRR, 80dB PSRR |
| Current - Output (Typ) | 50mA |
| Propagation Delay (Max) | 45μs |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MAX9120ESA Overview
In order to make transportation easier, it is packaged in 8-SOIC (0.154, 3.90mm Width) .A comparator with a CMOS, Open-Drain, Rail-to-Rail, TTL output is used here.The chip is packaged with Tube .Electronic comparator is possible to find the 8 terminals of the comparator.The chip belongs to Comparators .This is a typical comparator of type General Purpose .There are a total of 1 elements in it.A total of 5 pins are included.The recommended mounting type is Surface Mount .As a precaution, it is recommended to set the operating temperature to -40°C~85°C to prevent malfunctions.The comparator has a pin count of 8 .You can find more pin-to-pin solutions by searching MAX9120 .The PCB or other board can be mounted using the Surface Mount on it.Normally, the nominal supply current should be 800nA .A supply current exceeding 800nA may result in the comparator malfunctioning.In order to run the device, there are only 2/5V power supplies required.The part belongs to the series of comparator Beyond-the-Rails? .
MAX9120ESA Features
CMOS, Open-Drain, Rail-to-Rail, TTL output capability
General Purpose IC
Employing 1 elements
Operates under -40°C~85°C
MAX9120ESA Applications
There are a lot of Maxim Integrated MAX9120ESA linear comparators applications.
- Building automation
- Point of load regulators
- General Purpose Low Voltage Applications
- Battery-Powered Electronics
- Simple Analog-to-Digital Converters (ADCs)
- Consumer Medical Electronics
- Zero-Crossing Detectors
- Zero-Crossing Detectors
- Analog front end
- High-Speed Sampling Circuits
