MAX913ESA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 2003 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | with Latch |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Comparator |
| Max Power Dissipation | 471mW |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Base Part Number | MAX913 |
| Pin Count | 8 |
| Output Type | Complementary, TTL |
| Number of Circuits | 1 |
| Nominal Supply Current | 10mA |
| Output Current | 20mA |
| Max Supply Current | 10mA |
| Propagation Delay | 14 ns |
| Quiescent Current | 10mA |
| Turn On Delay Time | 16 ns |
| Response Time | 10 ns |
| Common Mode Rejection Ratio | 110 dB |
| Voltage - Supply, Single/Dual (±) | 5V~10V |
| Input Offset Voltage (Vos) | 2mV |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Voltage Gain | 70.88dB |
| Power Supply Rejection Ratio (PSRR) | 100dB |
| Supply Voltage Limit-Max | 7V |
| Dual Supply Voltage | 5V |
| Input Bias Current | 5μA |
| Neg Supply Voltage-Max (Vsup) | -7V |
| Voltage - Input Offset (Max) | 2mV @ ±5V |
| Current - Input Bias (Max) | 5μA @ ±5V |
| CMRR, PSRR (Typ) | 110dB CMRR, 100dB PSRR |
| Current - Output (Typ) | 20mA |
| Height | 1.5mm |
| Length | 5mm |
| Width | 4mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX913ESA+ Overview
In order to make transportation easier, it is packaged in 8-SOIC (0.154, 3.90mm Width) .Output type of this comparator is Complementary, TTL .Ready for shipping in Tube package.The comparator has 8 terminals.Electronic comparator is a component of the Comparator family.A comparator is capable of completing a variety of demanding tasks when supplied with 5V voltage.In general, the chip type can be classified as with Latch .As a result, it contains 8 pins.The type of mounting recommended is Surface Mount .Ideally, the operating temperature should be set at -40°C~85°C in order to prevent malfunction.There are 8 pins on the comparator.You can find more pin-to-pin solutions for your special requirements by searching MAX913 .There is a quiescent current of 10mA in this comparator.The PCB or other board has a Surface Mount for mounting.For normal use of the device, the nominal supply current should be 10mA .Electronic comparator is possible for the comparator to malfunction if the current supply exceeds 10mA .In accordance with the voltage formula, the part's voltage gain is 70.88dB .
MAX913ESA+ Features
Complementary, TTL output capability
with Latch IC
Operates under -40°C~85°C
Quiescent Current: 10mA
Voltage Gain: 70.88dB
MAX913ESA+ Applications
There are a lot of Maxim Integrated MAX913ESA+ linear comparators applications.
- Ultra-Low Power Systems
- Simple Analog-to-Digital Converters (ADCs)
- Metering Systems
- Portable and Battery-Powered Systems
- Power management
- Current and voltage sensing
- Laptop Computers
- Infotainment and Clusters
- Consumer Medical Electronics
- Point of load regulators
