MAX931EPA+
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 8-DIP (0.300, 7.62mm) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tube |
| Published | 1997 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | with Voltage Reference |
| Terminal Finish | Matte Tin (Sn) |
| Max Power Dissipation | 842mW |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MAX931 |
| Pin Count | 8 |
| Output Type | CMOS, TTL |
| Number of Elements | 1 |
| Supply Voltage-Min (Vsup) | 2.5V |
| Nominal Supply Current | 3.2μA |
| Output Current | 15μA |
| Max Supply Current | 3.2μA |
| Propagation Delay | 12 μs |
| Quiescent Current | 4μA |
| Common Mode Rejection Ratio | 80 dB |
| Voltage - Supply, Single/Dual (±) | 2.5V~11V ±1.25V~5.5V |
| Input Offset Voltage (Vos) | 10mV |
| Current - Quiescent (Max) | 4μA |
| Voltage - Input Offset (Max) | 10mV @ 5V |
| Hysteresis | 50mV |
| CMRR, PSRR (Typ) | 80dB CMRR, 80dB PSRR |
| Current - Output (Typ) | 0.015mA @ 5V |
| Height | 4.45mm |
| Length | 9.91mm |
| Width | 7.87mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX931EPA+ Overview
In order to make transportation easier, it is packaged in 8-DIP (0.300, 7.62mm) .Output type CMOS, TTL is used for this comparator.The part is shipped by Tube .The comparator has a total of 8 terminals.Supplied by 5V voltage, the comparator can accomplish the many demanding tasks.Electronic comparator is possible to classify the chip as with Voltage Reference .Electronic comparator has a total of 1 elements.The board includes 8 pins.The recommended mounting type is Through Hole .Ideally, the operating temperature should be set at -40°C~85°C in order to prevent malfunction.The comparator is equipped with 8 pins.You can search MAX931 if you are looking for more pin-to-pin solutions.The comparator presents a quiescent current of 4μA volts.The PCB or other board has a Through Hole for mounting.Normally, the nominal supply current should be 3.2μA when using the device.A current supply greater than 3.2μA may cause the comparator to malfunction.
MAX931EPA+ Features
CMOS, TTL output capability
with Voltage Reference IC
Employing 1 elements
Operates under -40°C~85°C
Quiescent Current: 4μA
MAX931EPA+ Applications
There are a lot of Maxim Integrated MAX931EPA+ linear comparators applications.
- Battery-Powered Electronics
- High-Speed Differential Line Receiver
- Power Supervision
- Factory automation & control
- Notebooks and PDAs
- Hand-Held Electronics
- Industrial
- Power management
- RC Timers
- Infotainment and Clusters
