MAX9915EXT+T
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Gold |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 6-TSSOP, SC-88, SOT-363 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2003 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL |
| Max Power Dissipation | 245mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 1.8V |
| Base Part Number | MAX9915 |
| Pin Count | 6 |
| Output Type | Rail-to-Rail |
| Power Supplies | 2/5V |
| Number of Channels | 1 |
| Operating Supply Current | 20μA |
| Nominal Supply Current | 20μA |
| Output Current | 15mA |
| Max Supply Current | 25μA |
| Slew Rate | 0.5V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 70 dB |
| Current - Input Bias | 1pA |
| Voltage - Supply, Single/Dual (±) | 1.8V~5.5V |
| Output Current per Channel | 15mA |
| Input Offset Voltage (Vos) | 200μV |
| Bandwidth | 1MHz |
| Unity Gain BW-Nom | 1000 kHz |
| Voltage Gain | 120dB |
| Average Bias Current-Max (IIB) | 0.00003μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 6V |
| Settling Time | 3.5 μs |
| Low-Bias | YES |
| Micropower | YES |
| Programmable Power | NO |
| Length | 2mm |
| Radiation Hardening | No |
| REACH SVHC | Unknown |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MAX9915EXT+T Overview
In the package, you will find a 6-TSSOP, SC-88, SOT-363-case to contain the op amp ic. There are two types of operational amplifiers in this circuit. The case in which buffer amplifier is delivered is called a Tape & Reel (TR) case. It is estimated that there will be 6 terminations in the next few months. The pins on this board total to 6 in total. This linear amplifier should be powered by an 1.8V battery. A type of Operational Amplifier op amp ic can be identified by the fact that this is a type of Operational Amplifier device. Linear amplifier includes 6 pins. With regards to the offset voltage of the input, buffer amplifier is rated at 200μV. For this electrical component, Surface Mount is the recommended mounting type. The buffer amplifier functions well at -40°C~85°C as far as operating temperature is concerned. Using a supply current of 20μA , this buffer op amp will be able to operate. It is recommended to keep the voltage gain at 120dB at all times. Buffer op amp is equipped with 1 channels on the device. As one of the many benefits of this buffer amplifier, it puts out Rail-to-Rail signals, which is one of the many benefits it offers. For the packing of the instrumentation amplifier, TAPE AND REEL is adopted.
MAX9915EXT+T Features
6 Pins
supply voltage of 1.8V
120dB voltage gain
Output Type: Rail-to-Rail
MAX9915EXT+T Applications
There are a lot of Maxim Integrated MAX9915EXT+T Instrumentational OP Amps applications.
- Industrial control system
- Weighing systems
- earphone
- Precision measurement
- Vehicle electronics
- High input resistance broadband
- Blood pressure sensors
- Portable docking station
- Signal amplification
- Video conversion and routing
