MC100EL30DWR2
| Parameters | |
|---|---|
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 100EL30 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 3 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Bits | 3 |
| Clock Frequency | 1.2GHz |
| Propagation Delay | 820 ps |
| Turn On Delay Time | 570 ps |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 62mA |
| Output Characteristics | OPEN-EMITTER |
| Trigger Type | Positive Edge |
| Number of Input Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 100EL |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
MC100EL30DWR2 Overview
The flip flop is packaged in 20-SOIC (0.295, 7.50mm Width). As part of the package Tape & Reel (TR), it is embedded. In the configuration, Differentialis used as the output. The trigger it is configured with uses Positive Edge. The electronic part is mounted in the way of Surface Mount. A -4.2V~-5.7Vsupply voltage is required for it to operate. It is at -40°C~85°C TAdegrees Celsius that the system is operating. There is D-Type type of electronic flip flop associated with this device. FPGAs belonging to the 100ELseries contain this type of chip. A frequency of 1.2GHzshould not be exceeded by its output. There are 3 elements in it. There is a consumption of 62mAof quiescent energy. 20terminations have occurred. You can search similar parts based on 100EL30. The D flip flop is powered by a voltage of 5V . There is an electronic part mounted in the way of Surface Mount. This board is designed with 20pins on it. This device has the clock edge trigger type of Positive Edge. It is included in FF/Latches. It is designed with a number of bits of 3. As soon as 5.7Vis reached, Vsup reaches its maximum value. Normally, the supply voltage (Vsup) should be above 4.2V. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. The D latch runs on a voltage of -4.5V volts. A total of 1input lines have been provided. Additionally, there are NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V on the electronic flip flop that can be referred to.
MC100EL30DWR2 Features
Tape & Reel (TR) package
100EL series
20 pins
3 Bits
-4.5V power supplies
MC100EL30DWR2 Applications
There are a lot of ON Semiconductor MC100EL30DWR2 Flip Flops applications.
- Differential Individual
- Synchronous counter
- Memory
- Storage registers
- Communications
- Single Down Count-Control Line
- High Performance Logic for test systems
- EMI reduction circuitry
- Count Modes
- Latch-up performance
