MC100EL31DTG
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 100EL31 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 2.8GHz |
| Propagation Delay | 590 ps |
| Turn On Delay Time | 465 ps |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 32mA |
| Halogen Free | Halogen Free |
| Trigger Type | Positive Edge |
| Power Supply Current-Max (ICC) | 37mA |
| fmax-Min | 2200 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 2000000000Hz |
| Height | 950μm |
| Length | 3.1mm |
| Width | 3.1mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2000 |
| Series | 100EL |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
MC100EL31DTG Overview
The flip flop is packaged in a case of 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). As part of the package Tube, it is embedded. As configured, the output uses Differential. This trigger uses the value Positive Edge. Surface Mountis occupied by this electronic component. A supply voltage of -4.2V~-5.7V is required for operation. A temperature of -40°C~85°C TAis used in the operation. There is D-Type type of electronic flip flop associated with this device. It is a type of FPGA belonging to the 100EL series. Its output frequency should not exceed 2.8GHz Hz. There is 32mA quiescent consumption. There are 8 terminations,It is a member of the 100EL31 family. It is powered from a supply voltage of 5V. Electronic part Surface Mountis mounted in the way. The 8pins are designed into the board. This device has Positive Edgeas its clock edge trigger type. There is a base part number FF/Latchesfor the RS flip flops. This flip flop is designed with 1 Bits. 5.7Vis the maximum supply voltage (Vsup). If you want to maintain normal operation, you should keep the supply voltage (Vsup) above 4.2V. Its flexibility is enhanced by 1 circuits. As a result of its reliability, this D flip flop is ideally suited for RAIL. A power supply of -4.5Vis required to operate it. In addition, NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7Vis a characteristic of it.
MC100EL31DTG Features
Tube package
100EL series
8 pins
1 Bits
-4.5V power supplies
MC100EL31DTG Applications
There are a lot of ON Semiconductor MC100EL31DTG Flip Flops applications.
- Load Control
- Shift Registers
- Computing
- Latch
- Event Detectors
- Convert a momentary switch to a toggle switch
- Modulo – n – counter
- Consumer
- Automotive
- 2 – Bit synchronous counter
