MC100EL51DG
| Parameters | |
|---|---|
| Packing Method | RAIL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 100EL51 |
| Function | Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Circuits | 1 |
| Output Current | 50mA |
| Number of Bits | 1 |
| Clock Frequency | 2.8GHz |
| Propagation Delay | 620 ps |
| Turn On Delay Time | 475 ps |
| Logic Function | Flip-Flop |
| Current - Quiescent (Iq) | 29mA |
| Max Input Voltage | 4.12V |
| Output Characteristics | OPEN-EMITTER |
| Halogen Free | Halogen Free |
| Prop. Delay@Nom-Sup | 0.62 ns |
| Trigger Type | Positive, Negative |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 36mA |
| fmax-Min | 2200 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2005 |
| Series | 100EL |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
MC100EL51DG Overview
The item is packaged in 8-SOIC (0.154, 3.90mm Width)cases. D flip flop is embedded in the Tube package. T flip flop is configured with an output of Differential. It is configured with the trigger Positive, Negative. In this case, the electronic component is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of -4.2V~-5.7V volts. The operating temperature is -40°C~85°C TA. The type of this D latch is D-Type. In FPGA terms, D flip flop is a type of 100ELseries FPGA. In order for it to function properly, its output frequency should not exceed 2.8GHz. T flip flop consumes 29mA quiescent energy. The number of terminations is 8. D latch belongs to the 100EL51 family. The power supply voltage is 5V. Electronic part Surface Mountis mounted in the way. It is designed with 8 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This part is included in FF/Latches. An electronic part designed with 1bits is used in this application. It reaches the maximum supply voltage (Vsup) at 5.7V. The supply voltage (Vsup) should be kept above 4.2V for normal operation. Using 1 circuits, it is highly flexible. Due to its reliability, this T flip flop is well suited for RAIL. A total of -4.5V power supplies are needed to run it. Its output current of 50mAallows for maximum design flexibility. Additionally, you may refer to the additional NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V of the electronic flip flop. 50mAis set as the high level output current. There is 50mA output current at the low level.
MC100EL51DG Features
Tube package
100EL series
8 pins
1 Bits
-4.5V power supplies
MC100EL51DG Applications
There are a lot of ON Semiconductor MC100EL51DG Flip Flops applications.
- Power down protection
- Asynchronous counter
- Functionally equivalent to the MC10/100EL29
- Shift registers
- Load Control
- Digital electronics systems
- Pattern generators
- Memory
- Latch-up performance
- Frequency Divider circuits
