MC100EL51DR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 100EL |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 100EL51 |
| Function | Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 2.8GHz |
| Propagation Delay | 565 ps |
| Turn On Delay Time | 475 ps |
| Logic Function | Flip-Flop |
| Current - Quiescent (Iq) | 29mA |
| Output Characteristics | OPEN-EMITTER |
| Halogen Free | Halogen Free |
| Prop. Delay@Nom-Sup | 0.62 ns |
| Trigger Type | Positive, Negative |
| Power Supply Current-Max (ICC) | 36mA |
| fmax-Min | 2200 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC100EL51DR2G Overview
The flip flop is packaged in 8-SOIC (0.154, 3.90mm Width). As part of the package Tape & Reel (TR), it is embedded. As configured, the output uses Differential. This trigger is configured to use Positive, Negative. There is an electrical part that is mounted in the way of Surface Mount. It operates with a supply voltage of -4.2V~-5.7V. In this case, the operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. This type of FPGA is a part of the 100EL series. A frequency of 2.8GHzshould be the maximum output frequency. There is a consumption of 29mAof quiescent energy. There have been 8 terminations. You can search similar parts based on 100EL51. The D flip flop is powered by a voltage of 5V . There is an electronic part that is mounted in the way of Surface Mount. This board has 8 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This RS flip flops is a part number FF/Latches. The design is based on 1bits. Vsup reaches its maximum value at 5.7V. Normally, the supply voltage (Vsup) should be above 4.2V. Its superior flexibility is attributed to its use of 1 circuits. A reliable performance of this D flip flop makes it well suited for use in TAPE AND REEL. It operates from -4.5V power supplies. Additionally, there are NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V on the electronic flip flop that can be referred to.
MC100EL51DR2G Features
Tape & Reel (TR) package
100EL series
8 pins
1 Bits
-4.5V power supplies
MC100EL51DR2G Applications
There are a lot of ON Semiconductor MC100EL51DR2G Flip Flops applications.
- Buffer registers
- Supports Live Insertion
- Test & Measurement
- CMOS Process
- Consumer
- Clock pulse
- Memory
- Power down protection
- Set-reset capability
- Control circuits
