MC100EL52DR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 100EL |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 100EL52 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 2.8GHz |
| Propagation Delay | 465 ps |
| Turn On Delay Time | 365 ps |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 25mA |
| Output Characteristics | OPEN-EMITTER |
| Trigger Type | Positive, Negative |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 29mA |
| fmax-Min | 2200 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 2200000000Hz |
| Length | 4.9mm |
| Width | 3.9mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC100EL52DR2 Overview
It is embeded in 8-SOIC (0.154, 3.90mm Width) case. A package named Tape & Reel (TR)includes it. T flip flop uses Differentialas its output configuration. It is configured with a trigger that uses Positive, Negative. Surface Mountis in the way of this electric part. A voltage of -4.2V~-5.7Vis used as the supply voltage. A temperature of -40°C~85°C TAis considered to be the operating temperature. A flip flop of this type is classified as a D-Type. This type of FPGA is a part of the 100EL series. There should be no greater frequency than 2.8GHzon its output. It consumes 25mA of quiescent A total of 8 terminations have been made. If you search by 100EL52, you will find similar parts. A voltage of 5V is used as the power supply for this D latch. It is mounted in the way of Surface Mount. The 8pins are designed into the board. A Positive Edgeclock edge trigger is used in this device. The part is included in FF/Latches. There are 1bits in this flip flop. It reaches the maximum supply voltage (Vsup) at 5.7V. A normal operating voltage (Vsup) should remain above 4.2V. Its flexibility is enhanced by 1 circuits. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. It operates from -4.5V power supplies. NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7Vis also one of its characteristics. A 50mAvalue is set for the high level output current. There is no low level output current set at 50mA.
MC100EL52DR2 Features
Tape & Reel (TR) package
100EL series
8 pins
1 Bits
-4.5V power supplies
MC100EL52DR2 Applications
There are a lot of ON Semiconductor MC100EL52DR2 Flip Flops applications.
- Data Synchronizers
- Count Modes
- Power down protection
- Control circuits
- Instrumentation
- Buffer registers
- High Performance Logic for test systems
- Digital electronics systems
- Common Clocks
- Divide a clock signal by 2 or 4
