MC100EP29DTR2
| Parameters | |
|---|---|
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 500 ps |
| Turn On Delay Time | 420 ps |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 57mA |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Number of Input Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2007 |
| Series | 100EP |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 100EP29 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 2 |
MC100EP29DTR2 Overview
20-TSSOP (0.173, 4.40mm Width)is the packaging method. A package named Tape & Reel (TR)includes it. The output it is configured with uses Differential. This trigger is configured to use Positive, Negative. Surface Mountis in the way of this electric part. Powered by a -3V~-5.5Vvolt supply, it operates as follows. The operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. This type of FPGA is a part of the 100EP series. Its output frequency should not exceed 3GHz Hz. In total, it contains 2 elements. Despite external influences, it consumes 57mAof quiescent current. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. You can search similar parts based on 100EP29. A voltage of 3.3V provides power to the D latch. There is an electronic part mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. This device's clock edge trigger type is Positive Edge. This device has the base part number FF/Latches. This flip flop is designed with 1 Bits. As soon as 5.5Vis reached, Vsup reaches its maximum value. Normal operation requires a supply voltage (Vsup) above 3V. Considering its reliability, this T flip flop is well suited for TAPE AND REEL. A total of -4.5V power supplies are needed to run it. This input has 1lines in it. As an additional reference, you may refer to electronic flip flop NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V. -50mAis the output current at high level. There is 50mA output current at the low level.
MC100EP29DTR2 Features
Tape & Reel (TR) package
100EP series
20 pins
1 Bits
-4.5V power supplies
MC100EP29DTR2 Applications
There are a lot of ON Semiconductor MC100EP29DTR2 Flip Flops applications.
- Shift Registers
- Data storage
- Safety Clamp
- Communications
- Dynamic threshold performance
- High Performance Logic for test systems
- ESCC
- Clock pulse
- Shift registers
- Power down protection
