MC100EP31DR2G
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 100EP |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3.0V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 100EP31 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 410 ps |
| Turn On Delay Time | 340 ps |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Halogen Free | Halogen Free |
| Trigger Type | Positive Edge |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000000Hz |
| Length | 4.9mm |
| Width | 3.9mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC100EP31DR2G Overview
8-SOIC (0.154, 3.90mm Width)is the way it is packaged. You can find it in the Tape & Reel (TR)package. It is configured with Differentialas an output. The trigger configured with it uses Positive Edge. There is an electrical part that is mounted in the way of Surface Mount. A -3V~-5.5Vsupply voltage is required for it to operate. It is operating at -40°C~85°C TA. A flip flop of this type is classified as a D-Type. In this case, it is a type of FPGA belonging to the 100EP series. In order for it to function properly, its output frequency should not exceed 3GHz. During its operation, it consumes 45mA quiescent energy. It has been determined that there have been 8 terminations. If you search by 100EP31, you will find similar parts. A voltage of 3.3V is used to power it. There is an electronic part that is mounted in the way of Surface Mount. This board has 8 pins. This device has Positive Edgeas its clock edge trigger type. The RS flip flops belongs to FF/Latches base part number. An electronic part designed with 1bits is used in this application. In this case, the maximum supply voltage (Vsup) reaches 5.5V. Keeping the supply voltage (Vsup) above 3V is necessary for normal operation. The superior flexibility is achieved through the use of 1 circuits. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. The system runs on a power supply of -4.5V watts. There is also a characteristic of NECL MODE: VCC = 0V WITH VEE = -3.0V TO -5.5V.
MC100EP31DR2G Features
Tape & Reel (TR) package
100EP series
8 pins
1 Bits
-4.5V power supplies
MC100EP31DR2G Applications
There are a lot of ON Semiconductor MC100EP31DR2G Flip Flops applications.
- Data Synchronizers
- Memory
- Asynchronous counter
- Counters
- ATE
- Functionally equivalent to the MC10/100EL29
- Bus hold
- Divide a clock signal by 2 or 4
- Frequency Dividers
- Consumer
