MC100EP51DTR2
| Parameters | |
|---|---|
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 100EP51 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -4.5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 450 ps |
| Turn On Delay Time | 375 ps |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 45mA |
| Prop. Delay@Nom-Sup | 0.5 ns |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 47mA |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000000Hz |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 100EP |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
MC100EP51DTR2 Overview
The item is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width)cases. The Tape & Reel (TR)package contains it. T flip flop uses Differentialas its output configuration. In the configuration of the trigger, Positive, Negativeis used. There is an electric part mounted in the way of Surface Mount. The supply voltage is set to -3V~-5.5V. -40°C~85°C TAis the operating temperature. There is D-Type type of electronic flip flop associated with this device. FPGAs belonging to the 100EPseries contain this type of chip. A frequency of 3GHzshould not be exceeded by its output. This process consumes 45mA quiescents. Currently, there are 8 terminations. It is a member of the 100EP51 family. It is powered by a voltage of 3.3V . There is an electronic part that is mounted in the way of Surface Mount. With its 8pins, it is designed to work with most electronic flip flops. This device's clock edge trigger type is Positive Edge. The part you are looking for is included in FF/Latches. There are 1bits in this flip flop. It reaches the maximum supply voltage (Vsup) at 5.5V. It is imperative that the supply voltage (Vsup) is maintained above 3Vin order to ensure normal operation. The superior flexibility is achieved through the use of 1 circuits. Compared to other similar T flip flops, this device offers reliable performance and is well suited for TAPE AND REEL. An electrical current of -4.5V volts is applied to it. Additionally, you may refer to the additional NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V of the electronic flip flop. It is set to -50mAfor the high level output current. 50mA is the low level output current.
MC100EP51DTR2 Features
Tape & Reel (TR) package
100EP series
8 pins
1 Bits
-4.5V power supplies
MC100EP51DTR2 Applications
There are a lot of ON Semiconductor MC100EP51DTR2 Flip Flops applications.
- Count Modes
- Latch
- Consumer
- Patented noise
- Test & Measurement
- Memory
- Matched Rise and Fall
- Event Detectors
- CMOS Process
- Shift Registers
