banner_page

MC10E156FN

28 Terminations±4.2V~5.7V Signal switch10E Series 1 Functions


  • Manufacturer: Rochester Electronics, LLC
  • Nocochips NO: 699-MC10E156FN
  • Package: 28-LCC (J-Lead)
  • Datasheet: PDF
  • Stock: 415
  • Description: 28 Terminations±4.2V~5.7V Signal switch10E Series 1 Functions(Kg)

Details

Tags

Parameters
Mounting Type Surface Mount
Package / Case 28-LCC (J-Lead)
Surface Mount YES
Operating Temperature 0°C~85°C
Packaging Tube
Series 10E
JESD-609 Code e0
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 28
Type Multiplexer
Terminal Finish TIN LEAD
Additional Feature NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V
Technology ECL
Voltage - Supply ±4.2V~5.7V
Terminal Position QUAD
Terminal Form J BEND
Peak Reflow Temperature (Cel) 240
Number of Functions 1
Supply Voltage 5V
Time@Peak Reflow Temperature-Max (s) 30
Pin Count 28
JESD-30 Code S-PQCC-J28
Qualification Status COMMERCIAL
Circuit 3 x 4:1
Supply Voltage-Max (Vsup) 5.7V
Supply Voltage-Min (Vsup) 4.2V
Number of Bits 3
Family 10E
Output Characteristics OPEN-EMITTER
Output Polarity COMPLEMENTARY
Propagation Delay (tpd) 0.8 ns
Voltage Supply Source Dual Supply
Independent Circuits 1
fmax-Min 700 MHz
Height Seated (Max) 4.57mm
RoHS Status Non-RoHS Compliant

MC10E156FN Overview


Due to the fact that it is provided in the 28-LCC (J-Lead), digital switch allows the board to be compacted.The package is packaged in accordance with Tube.Digital switch ic uses a Surface Mount mounting method.the multiplexers uses an analog IC Multiplexer.In the case of 0°C~85°C, turn signal switch will not be affected by external factors.Designers have greater flexibility using digital controlled switch when it works with ±4.2V~5.7V voltage.Multiplexers from the 10E series can be used in a wide range of applications.Among its basic configurations are 28 terminations.The multiplexer's system is powered by 5V voltage.Currently, this turn signal switch has a total of 28 component pins.As the end of conductors, it uses J BEND.The logic switch is a member of the family of 10E.There are 3 bits in signal multiplexer.It is recommended that the minimum supply voltage (Vsup) be kept at 4.2V so that unnecessary failures can be prevented.It is advisable to keep the maximum supply voltage (Vsup) at 5.7V so as to avoid some unnecessary failures.Additionally, it improves the characteristics of NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V.

MC10E156FN Features


Supplied in the 28-LCC (J-Lead) package
NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V

MC10E156FN Applications


There are a lot of Rochester Electronics, LLC MC10E156FN Signal Switches / Multiplexers / Decoders applications.

  • To select different devices in microprocessor output
  • Recording transmission
  • Small scale TV wall
  • PCIe
  • Make full adder
  • Electronics industry
  • GLAN
  • Code conversion
  • Speed synchronization of multiple motors in industries
  • Time division multiplexing system

Write a review

Note: HTML is not translated!
    Bad           Good