MC10EL51DTR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2008 |
| Series | 10EL |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 8 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.2V~-5.7V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 10EL51 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.7V |
| Power Supplies | -5.2V |
| Supply Voltage-Min (Vsup) | 4.2V |
| Number of Circuits | 1 |
| Number of Bits | 1 |
| Clock Frequency | 2.8GHz |
| Propagation Delay | 565 ps |
| Turn On Delay Time | 475 ps |
| Logic Function | Flip-Flop |
| Current - Quiescent (Iq) | 29mA |
| Halogen Free | Halogen Free |
| Prop. Delay@Nom-Sup | 0.62 ns |
| Trigger Type | Positive, Negative |
| Power Supply Current-Max (ICC) | 29mA |
| fmax-Min | 2200 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 2200000000Hz |
| Length | 3mm |
| Width | 3mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC10EL51DTR2G Overview
As a result, it is packaged as 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Package Tape & Reel (TR)embeds it. It is configured with Differentialas an output. It is configured with a trigger that uses a value of Positive, Negative. The electronic part is mounted in the way of Surface Mount. A voltage of -4.2V~-5.7Vis required for its operation. It is at -40°C~85°C TAdegrees Celsius that the system is operating. The type of this D latch is D-Type. The FPGA belongs to the 10EL series. Its output frequency should not exceed 2.8GHz. It consumes 29mA of quiescent current without being affected by external factors. There have been 8 terminations. It is a member of the 10EL51 family. Power is supplied from a voltage of 5V volts. This electronic part is mounted in the way of Surface Mount. A total of 8pins are provided on this board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is included in FF/Latches. There are 1bits in this flip flop. The maximal supply voltage (Vsup) reaches 5.7V. Normal operation requires a supply voltage (Vsup) above 4.2V. Its superior flexibility is attributed to its use of 1 circuits. As a result of its reliable performance, this T flip flop is suitable for TAPE AND REEL. An electrical current of -5.2V volts is applied to it. Additionally, you may refer to the D latch's additional NECL MODE: VCC = 0V WITH VEE = -4.2V TO -5.7V.
MC10EL51DTR2G Features
Tape & Reel (TR) package
10EL series
8 pins
1 Bits
-5.2V power supplies
MC10EL51DTR2G Applications
There are a lot of ON Semiconductor MC10EL51DTR2G Flip Flops applications.
- Convert a momentary switch to a toggle switch
- Data transfer
- Common Clocks
- Test & Measurement
- Buffered Clock
- ESD performance
- QML qualified product
- EMI reduction circuitry
- Consumer
- ATE
