MC10EP29DT
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2007 |
| Series | 10EP |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 10EP29 |
| Function | Set(Preset) and Reset |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Bits | 1 |
| Clock Frequency | 3GHz |
| Propagation Delay | 500 ps |
| Turn On Delay Time | 420 ps |
| Family | 10E |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 57mA |
| Trigger Type | Positive, Negative |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Power Supply Current-Max (ICC) | 60mA |
| Number of Input Lines | 1 |
| Length | 6.5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Lead Free |
MC10EP29DT Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). You can find it in the Tubepackage. Currently, the output is configured to use Differential. This trigger uses the value Positive, Negative. There is an electronic component mounted in the way of Surface Mount. A voltage of -3V~-5.5Vis required for its operation. In this case, the operating temperature is -40°C~85°C TA. It belongs to the type D-Typeof flip flops. FPGAs belonging to the 10EPseries contain this type of chip. You should not exceed 3GHzin the output frequency of the device. A total of 2elements are contained within it. This process consumes 57mA quiescents. The number of terminations is 20. D latch belongs to the 10EP29 family. The power source is powered by 3.3V. A device of this type belongs to the family of 10E. Electronic part Surface Mountis mounted in the way. It is designed with 20 pins. It is part of the FF/Latchesbase part number family. There are 1bits in this flip flop. The maximal supply voltage (Vsup) reaches 5.5V. It is imperative that the supply voltage (Vsup) is maintained above 3Vin order to ensure normal operation. In view of its reliability, this D flip flop is a good fit for RAIL. Currently, there are 1 lines of input. Additionally, it is characterized by NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V. In this case, the high level output current is set to -50mA. There is no low level output current set at 50mA.
MC10EP29DT Features
Tube package
10EP series
20 pins
1 Bits
MC10EP29DT Applications
There are a lot of ON Semiconductor MC10EP29DT Flip Flops applications.
- Modulo – n – counter
- Communications
- Data Synchronizers
- 2 – Bit synchronous counter
- High Performance Logic for test systems
- Set-reset capability
- Instrumentation
- Guaranteed simultaneous switching noise level
- Counters
- QML qualified product
