MC10EP451FAR2
| Parameters | |
|---|---|
| Clock Frequency | 3GHz |
| Propagation Delay | 550 ps |
| Turn On Delay Time | 650 ps |
| Family | 10E |
| Current - Quiescent (Iq) | 125mA |
| Trigger Type | Positive Edge |
| High Level Output Current | -50mA |
| Low Level Output Current | 50mA |
| Number of Input Lines | 6 |
| Count Direction | RIGHT |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 3000000000Hz |
| Length | 7mm |
| Width | 7mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 32-LQFP |
| Number of Pins | 32 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2002 |
| Series | 10EP |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 32 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Additional Feature | NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V |
| Subcategory | Shift Registers |
| Technology | ECL |
| Voltage - Supply | -3V~-5.5V |
| Terminal Position | QUAD |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 3.3V |
| Terminal Pitch | 0.8mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 10EP451 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | -5.2V |
| Supply Voltage-Min (Vsup) | 3V |
| Number of Bits | 6 |
MC10EP451FAR2 Overview
The item is packaged in 32-LQFPcases. D flip flop is embedded in the Tape & Reel (TR) package. T flip flop is configured with an output of Differential. It is configured with the trigger Positive Edge. Surface Mountis occupied by this electronic component. It operates with a supply voltage of -3V~-5.5V. A temperature of -40°C~85°C TAis used in the operation. This electronic flip flop is of type D-Type. FPGAs belonging to the 10EPseries contain this type of chip. This D flip flop should not have a frequency greater than 3GHz. A total of 1 elements are present. It consumes 125mA of quiescent current without being affected by external factors. There have been 32 terminations. If you search by 10EP451, you will find similar parts. The D flip flop is powered by a voltage of 3.3V . In this case, the D flip flop belongs to the 10Efamily. This electronic part is mounted in the way of Surface Mount. With its 32pins, it is designed to work with most electronic flip flops. The clock edge trigger type for this device is Positive Edge. It is included in Shift Registers. 6bits are used in its design. It reaches 5.5Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be kept above 3V. There are -5.2V power supplies attached to it. There are 6 input Lines, which consist of an electronic circuit connected between the ac mains and the rectifier input stage of the switching power supply. It is also characterized by NECL MODE: VCC = 0V WITH VEE = -3V TO -5.5V. -50mAis set as the high level output current. It is set to 50mAfor low level output current.
MC10EP451FAR2 Features
Tape & Reel (TR) package
10EP series
32 pins
6 Bits
-5.2V power supplies
MC10EP451FAR2 Applications
There are a lot of ON Semiconductor MC10EP451FAR2 Flip Flops applications.
- Modulo – n – counter
- Control circuits
- Frequency Dividers
- Set-reset capability
- ATE
- Circuit Design
- Instrumentation
- Latch-up performance
- Latch
- QML qualified product
