MC10H176FN
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~75°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 10H |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | ECL |
| Voltage - Supply | -4.9V~-5.46V |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 240 |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 10H176 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 7 |
| Number of Bits | 6 |
| Clock Frequency | 250MHz |
| Propagation Delay | 2.2 ns |
| Turn On Delay Time | 1 ns |
| Family | 10H |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 112mA |
| Output Characteristics | OPEN-EMITTER |
| Trigger Type | Positive Edge |
| Number of Output Lines | 6 |
| fmax-Min | 250 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 250000000Hz |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC10H176FN Overview
In the form of 20-LCC (J-Lead), it has been packaged. As part of the package Tube, it is embedded. As configured, the output uses Non-Inverted. In the configuration of the trigger, Positive Edgeis used. In this case, the electronic component is mounted in the way of Surface Mount. A supply voltage of -4.9V~-5.46V is required for operation. It is at 0°C~75°C TAdegrees Celsius that the system is operating. A flip flop of this type is classified as a D-Type. It is a type of FPGA belonging to the 10H series. It should not exceed 250MHzin its output frequency. In total, there are 1 elements. It consumes 112mA of quiescent current without being affected by external factors. In 20terminations, a transmission line is terminated with a JK flip flop that matches its characteristic impedance. If you search by 10H176, you will find similar parts. An electronic device belonging to the family 10Hcan be found here. There is an electronic component mounted in the way of Surface Mount. This board has 20 pins. There is a clock edge trigger type of Positive Edgeon this device. The part is included in FF/Latches. There are 6bits in its design. The superior flexibility of this product is achieved by using 7 circuits. Due to its reliability, this T flip flop is well suited for RAIL. There are 6 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code.
MC10H176FN Features
Tube package
10H series
20 pins
6 Bits
MC10H176FN Applications
There are a lot of ON Semiconductor MC10H176FN Flip Flops applications.
- Set-reset capability
- Asynchronous counter
- Power down protection
- ESCC
- Memory
- Storage Registers
- Bus hold
- Consumer
- Computers
- High Performance Logic for test systems
