MC10H186FN
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~75°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 10H |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Technology | ECL |
| Voltage - Supply | -4.9V~-5.46V |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 240 |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 10H186 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 7 |
| Number of Bits | 6 |
| Clock Frequency | 250MHz |
| Propagation Delay | 3 ns |
| Turn On Delay Time | 1 ns |
| Family | 10H |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 110mA |
| Output Characteristics | OPEN-EMITTER |
| Trigger Type | Positive Edge |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Number of Output Lines | 6 |
| fmax-Min | 250 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 250000000Hz |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC10H186FN Overview
As a result, it is packaged as 20-LCC (J-Lead). D flip flop is embedded in the Tube package. T flip flop uses Non-Invertedas the output. JK flip flop uses Positive Edgeas the trigger. This electronic part is mounted in the way of Surface Mount. The JK flip flop operates at -4.9V~-5.46Vvolts. In this case, the operating temperature is 0°C~75°C TA. It is an electronic flip flop with the type D-Type. It belongs to the 10Hseries of FPGAs. This D flip flop should not have a frequency greater than 250MHz. A total of 1elements are contained within it. During its operation, it consumes 110mA quiescent energy. It has been determined that there have been 20 terminations. JK flip flop belongs to 10H186 family. In this case, the D flip flop belongs to the 10Hfamily. There is an electronic component mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. A Positive Edgeclock edge trigger is used in this device. It is part of the FF/Latchesbase part number family. An electronic part designed with 6bits is used in this application. The superior flexibility is achieved through the use of 7 circuits. In order to operate, the chip has 6 output lines. In this case, the high level output current is set to 50mA. 50mA is the low level output current.
MC10H186FN Features
Tube package
10H series
20 pins
6 Bits
MC10H186FN Applications
There are a lot of ON Semiconductor MC10H186FN Flip Flops applications.
- Computers
- Buffered Clock
- Functionally equivalent to the MC10/100EL29
- Control circuits
- Modulo – n – counter
- Memory
- Count Modes
- Automotive
- Frequency division
- Latch
