MC10H186FNR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Number of Pins | 20 |
| Operating Temperature | 0°C~75°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | 10H |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | ECL |
| Voltage - Supply | -4.9V~-5.46V |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 240 |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 10H186 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 7 |
| Number of Bits | 6 |
| Clock Frequency | 250MHz |
| Propagation Delay | 3 ns |
| Turn On Delay Time | 1 ns |
| Family | 10H |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 110mA |
| Output Characteristics | OPEN-EMITTER |
| Trigger Type | Positive Edge |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Number of Output Lines | 6 |
| fmax-Min | 250 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 250000000Hz |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC10H186FNR2 Overview
The package is in the form of 20-LCC (J-Lead). D flip flop is embedded in the Tape & Reel (TR) package. Non-Invertedis the output configured for it. It is configured with a trigger that uses a value of Positive Edge. In this case, the electronic component is mounted in the way of Surface Mount. A supply voltage of -4.9V~-5.46V is required for operation. The operating temperature is 0°C~75°C TA. The type of this D latch is D-Type. It belongs to the 10Hseries of FPGAs. A frequency of 250MHzshould not be exceeded by its output. D latch consists of 1 elements. As a result, it consumes 110mA of quiescent current without being affected by external factors. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 10H186 family contains it. The electronic device belongs to the 10Hfamily. Surface Mount mounts this electronic component. Basically, it is designed with a set of 20 pins. This device has Positive Edgeas its clock edge trigger type. There is a base part number FF/Latchesfor the RS flip flops. An electronic part with 6bits has been designed. Despite its superior flexibility, it relies on 7 circuits to achieve it. Considering the reliability of this T flip flop, it is well suited for TAPE AND REEL. To operate, the chip has a total of 6 output lines. A high level output current of 50mAis set. In the low level output current setting, the current is set to 50mA.
MC10H186FNR2 Features
Tape & Reel (TR) package
10H series
20 pins
6 Bits
MC10H186FNR2 Applications
There are a lot of ON Semiconductor MC10H186FNR2 Flip Flops applications.
- Consumer
- Computing
- Memory
- Frequency division
- Count Modes
- Safety Clamp
- Pattern generators
- Data Synchronizers
- Modulo – n – counter
- Load Control
