MC10H186L
| Parameters | |
|---|---|
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 16-CDIP (0.300, 7.62mm) |
| Number of Pins | 16 |
| Operating Temperature | 0°C~75°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 10H |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Technology | ECL |
| Voltage - Supply | -4.9V~-5.46V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 235 |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 10H186 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Number of Circuits | 7 |
| Number of Bits | 6 |
| Clock Frequency | 250MHz |
| Propagation Delay | 3 ns |
| Turn On Delay Time | 1 ns |
| Family | 10H |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 110mA |
| Output Characteristics | OPEN-EMITTER |
| Trigger Type | Positive Edge |
| High Level Output Current | 50mA |
| Low Level Output Current | 50mA |
| Number of Output Lines | 6 |
| fmax-Min | 250 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 250000000Hz |
| Height Seated (Max) | 5.08mm |
MC10H186L Overview
16-CDIP (0.300, 7.62mm)is the packaging method. The Tubepackage contains it. The output it is configured with uses Non-Inverted. The trigger it is configured with uses Positive Edge. Through Holemounts this electrical part. Powered by a -4.9V~-5.46Vvolt supply, it operates as follows. Temperature is set to 0°C~75°C TA. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 10H series. In order for it to function properly, its output frequency should not exceed 250MHz. There are 1 elements in it. T flip flop consumes 110mA quiescent energy. Currently, there are 16 terminations. You can search similar parts based on 10H186. This D flip flop belongs to the family of 10H. Through Hole mounts this electronic component. The 16pins are designed into the board. There is a clock edge trigger type of Positive Edgeon this device. This RS flip flops is a part number FF/Latches. 6bits are used in its design. In order to achieve its superior flexibility, 7 circuits are used. In order to operate, the chip has 6 output lines. The high level output current is set to 50mA. In the low level output current setting, the current is set to 50mA.
MC10H186L Features
Tube package
10H series
16 pins
6 Bits
MC10H186L Applications
There are a lot of ON Semiconductor MC10H186L Flip Flops applications.
- Modulo – n – counter
- ESD performance
- Balanced Propagation Delays
- Reduced system switching noise
- Communications
- Common Clocks
- Buffered Clock
- Patented noise
- Control circuits
- Storage Registers
