MC14013BFEL
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 4000B |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 3V~18V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 4013 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Min (Vsup) | 3V |
| Load Capacitance | 50pF |
| Number of Bits | 1 |
| Clock Frequency | 14MHz |
| Propagation Delay | 350 ns |
| Turn On Delay Time | 50 ns |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 8.8mA 8.8mA |
| Max Propagation Delay @ V, Max CL | 100ns @ 15V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 5pF |
| Number of Output Lines | 1 |
| fmax-Min | 7 MHz |
| Clock Edge Trigger Type | Positive Edge |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC14013BFEL Overview
The package is in the form of 14-SOIC (0.209, 5.30mm Width). It is included in the package Tape & Reel (TR). T flip flop is configured with an output of Differential. It is configured with a trigger that uses a value of Positive Edge. This electronic part is mounted in the way of Surface Mount. The supply voltage is set to 3V~18V. In this case, the operating temperature is -55°C~125°C TA. It is an electronic flip flop with the type D-Type. FPGAs belonging to the 4000Bseries contain this type of chip. It should not exceed 14MHzin terms of its output frequency. In total, it contains 2 elements. During its operation, it consumes 4μA quiescent energy. Terminations are 14. The object belongs to the 4013 family. Power is supplied from a voltage of 5V volts. JK flip flop input capacitance is 5pF farads. This electronic part is mounted in the way of Surface Mount. The 14pins are designed into the board. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This part is included in FF/Latches. The flip flop is designed with 1bits. It is imperative that the supply voltage (Vsup) is maintained above 3Vin order to ensure normal operation. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. There are 1 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code.
MC14013BFEL Features
Tape & Reel (TR) package
4000B series
14 pins
1 Bits
MC14013BFEL Applications
There are a lot of ON Semiconductor MC14013BFEL Flip Flops applications.
- Event Detectors
- Automotive
- Storage registers
- Asynchronous counter
- Counters
- 2 – Bit synchronous counter
- Balanced Propagation Delays
- Balanced 24 mA output drivers
- Frequency Dividers
- Digital electronics systems
