banner_page

MC14052BCPG

DP4T 280Ohm Analog Switches BREAK-BEFORE-MAKE MC14052B 16 Pins 100nA 5V 16-DIP (0.300, 7.62mm)


  • Manufacturer: ON Semiconductor
  • Nocochips NO: 598-MC14052BCPG
  • Package: 16-DIP (0.300, 7.62mm)
  • Datasheet: PDF
  • Stock: 838
  • Description: DP4T 280Ohm Analog Switches BREAK-BEFORE-MAKE MC14052B 16 Pins 100nA 5V 16-DIP (0.300, 7.62mm)(Kg)

Details

Tags

Parameters
Mounting Type Through Hole
Package / Case 16-DIP (0.300, 7.62mm)
Surface Mount NO
Number of Pins 16
Operating Temperature -55°C~125°C TA
Packaging Tube
Published 2002
JESD-609 Code e3
Pbfree Code yes
Part Status Obsolete
Moisture Sensitivity Level (MSL) 1 (Unlimited)
Number of Terminations 16
Resistance 1.05kOhm
Terminal Finish Tin (Sn)
Subcategory Multiplexer or Switches
Max Power Dissipation 500mW
Technology CMOS
Number of Functions 1
Supply Voltage 5V
Base Part Number MC14052B
Pin Count 16
Power Supplies 5/15V
Number of Channels 4
Max Supply Voltage 18V
Min Supply Voltage 3V
Analog IC - Other Type DIFFERENTIAL MULTIPLEXER
Nominal Supply Current 15nA
Power Dissipation 500mW
Propagation Delay 75 ns
Turn On Delay Time 600 ns
Logic Function Demultiplexer, Multiplexer
Number of Inputs 8
Supply Type Dual
Bandwidth 17MHz
Turn-Off Delay Time 600 ns
Number of Gates 2
On-State Resistance (Max) 280Ohm
Multiplexer/Demultiplexer Circuit 2:4
Off-state Isolation-Nom 50 dB
Current - Leakage (IS(off)) (Max) 100nA
Channel Capacitance (CS(off), CD(off)) 7.5pF
On-state Resistance Match-Nom 25Ohm
Switch Circuit DP4T
Channel-to-Channel Matching (ΔRon) 10 Ω
Switching BREAK-BEFORE-MAKE
Voltage - Supply, Single (V+) 3V~18V
Drain to Source Resistance 80Ohm
Height 3.429mm
Length 19.5326mm
Width 6.858mm
Radiation Hardening No
REACH SVHC No SVHC
RoHS Status RoHS Compliant
Lead Free Lead Free

MC14052BCPG Overview


This electronic part is conveniently packaged in 16-DIP (0.300, 7.62mm), making it easy to ship abroad. This packaging method provides high reliability because it uses advanced packaging techniques. Through Hole is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 2:4. Operating temperature extended to -55°C~125°C TA. Totally, there are 16 terminations. A high-quality output is provided by the electrical component's 4 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. Into the electrical component body are injected 16 pins. Multiplexers built on a DP4T switching circuit are built. Try searching for the analog switch ic with MC14052B if you are looking for variants. A 1.05kOhm internal resistance characterizes this multiplexer. For functions related to 16 pins, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Users should never supply a voltage higher than 18V to a switch device. Analogue multiplexer with a Dual supply type that is cost-effective. It is recommended to use 3V as the lowest voltage for the electrical part. Using only a single voltage supply, this analog switch requires 3V~18V voltage. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. It is possible to operate 8 inputs. In 17MHz-bandwidths, data can be transferred. Resistivity from Drain to Source is 80Ohm for this electronic part.

MC14052BCPG Features


4 Channels
Switch Circuit: DP4T
Bandwidth: 17MHz
Drain-to-Source resistance: 80Ohm

MC14052BCPG Applications


There are a lot of ON Semiconductor MC14052BCPG Analog Switches & Multiplexers ICs applications.

  • Communications systems
  • DSLAMs
  • HDTV
  • Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
  • Avionics test equipment
  • Frame Relay Equipment
  • Microprocessor Controlled Analog Systems
  • SONET/SDH ADM
  • SDH/SONET multiplexers
  • Data switching

Write a review

Note: HTML is not translated!
    Bad           Good