MC14052BDTR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Contact Plating | Gold |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2004 |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 280Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MC14052B |
| Pin Count | 16 |
| Power Supplies | 5/15V |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Power Dissipation | 500mW |
| Propagation Delay | 75 ns |
| Turn On Delay Time | 600 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Halogen Free | Halogen Free |
| Supply Type | Dual |
| Bandwidth | 17MHz |
| Turn-Off Delay Time | 600 ns |
| On-State Resistance (Max) | 280Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 2:4 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF |
| On-state Resistance Match-Nom | 25Ohm |
| Switch Circuit | DP4T |
| Channel-to-Channel Matching (ΔRon) | 10 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~18V |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC14052BDTR2G Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. A switch device like this is mounted in Surface Mount. 2:4 is the ratio between multiplexers and demultiplexers. Around -55°C~125°C TA is the extended operating temperature. The total number of terminations is 16. As a result of its 4 channels, this electronic component provides high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. There are 16 pins injected into the electronic part body. On the other hand, analog switches can be constructed using DP4T switching circuits. The multiplexer consists of 2 circuits. Try searching for the analog switch ic with MC14052B if you are looking for variants. There is 280Ohm internal resistance in this digital multiplexer. The functions of 16 pins can be found in the datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 18V. A cost-effective Dual supply type analogue multiplexer. 3V should be the lowest voltage fed to the electronic component. An analogue multiplexer drains from a single voltage supply at 3V~18V. It is integrated with a DIFFERENTIAL MULTIPLEXER analog IC. Operating the 8 inputs requires 8 inputs. 17MHz bandwidths enable data to be transferred.
MC14052BDTR2G Features
4 Channels
Switch Circuit: DP4T
Bandwidth: 17MHz
MC14052BDTR2G Applications
There are a lot of ON Semiconductor MC14052BDTR2G Analog Switches & Multiplexers ICs applications.
- Communications systems
- ATM
- Communication systems
- Video signal routing
- Cable PC
- Power routing
- RGB switches
- Mechanical reed relay replacement
- Avionics test equipment
- Intelligent PBX
