MC14053BCPG
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 1.05kOhm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Number of Functions | 3 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | MC14053B |
| Pin Count | 16 |
| Power Supplies | 5/15V |
| Number of Channels | 2 |
| Voltage | 18V |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 500mW |
| Propagation Delay | 65 ns |
| Turn On Delay Time | 550 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 6 |
| Supply Type | Dual |
| Bandwidth | 17MHz |
| Turn-Off Delay Time | 550 ns |
| Number of Gates | 3 |
| On-State Resistance (Max) | 280Ohm |
| High Level Output Current | 25mA |
| Low Level Output Current | 25mA |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 7.5pF |
| On-state Resistance Match-Nom | 25Ohm |
| Switch Circuit | SPDT |
| Channel-to-Channel Matching (ΔRon) | 10 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Voltage - Supply, Single (V+) | 3V~18V |
| Signal Current-Max | 0.025A |
| Height | 3.43mm |
| Length | 19.55mm |
| Width | 6.85mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC14053BCPG Overview
Packed in 16-DIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tube. The multiplexer is located in Through Hole. Multiplexers and demultiplexers have a ratio of 2:1. Temperatures around -55°C~125°C TA are extended for operation. 16 terminations have been made so far. The electronic part provides high-quality output because it has 2 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Based on SPDT switching circuits, these analog multiplexers work. Look for analog switch ic variants by searching with MC14053B. As far as internal resistance is concerned, it has 1.05kOhm. Datasheets for functions of 16 pins are available. It is a typical Multiplexer or Switches analog multiplexer. An abnormal situation would be for the switch device to be supplied with a voltage greater than 18V. The analog switch ic is of the Dual supply type and is cost-effective. It is recommended to use 3V as the lowest voltage for the electrical part. Analogue multiplexers require a 3V~18V voltage to drain from a single voltage supply. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. There are 6 inputs to be operated. 17MHz-bandwidths can be used to transfer data between multiplexers.
MC14053BCPG Features
2 Channels
Switch Circuit: SPDT
Bandwidth: 17MHz
MC14053BCPG Applications
There are a lot of ON Semiconductor MC14053BCPG Analog Switches & Multiplexers ICs applications.
- Communication systems
- Audio signal routing
- Battery Powered Instruments
- Cable Modem
- Automotive applications
- FTTH
- T1/E1 Terminals
- E1 Multiplexer
- Relay replacements
- Central office
