Parameters |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.209, 5.30mm Width) |
Number of Pins |
16 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
Published |
2006 |
JESD-609 Code |
e4 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
16 |
Resistance |
280Ohm |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
500mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
MC14053B |
Pin Count |
16 |
Power Supplies |
5/15V |
Number of Channels |
2 |
Number of Circuits |
3 |
Max Supply Voltage |
18V |
Min Supply Voltage |
3V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Operating Supply Current |
360nA |
Power Dissipation |
500mW |
Propagation Delay |
65 ns |
Turn On Delay Time |
550 ns |
Logic Function |
Demultiplexer, Demux, Multiplexer, Mux |
Number of Inputs |
6 |
Supply Type |
Dual |
Bandwidth |
17MHz |
Turn-Off Delay Time |
550 ns |
On-State Resistance (Max) |
280Ohm |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
50 dB |
Current - Leakage (IS(off)) (Max) |
100nA |
Channel Capacitance (CS(off), CD(off)) |
7.5pF |
On-state Resistance Match-Nom |
25Ohm |
Switch Circuit |
SPDT |
Channel-to-Channel Matching (ΔRon) |
10 Ω |
Switching |
BREAK-BEFORE-MAKE |
Voltage - Supply, Single (V+) |
3V~18V |
Signal Current-Max |
0.025A |
Height Seated (Max) |
2.05mm |
Length |
10.2mm |
Radiation Hardening |
No |
RoHS Status |
RoHS Compliant |
Lead Free |
Lead Free |
MC14053BFELG Overview
Presented in 16-SOIC (0.209, 5.30mm Width), this electrical component is convenient for overseas shipping. In order to provide high reliability, an advanced packaging method Tape & Reel (TR) is used. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 2:1. Operation at a temperature around -55°C~125°C TA. A total of 16 terminations have been recorded. A 2 channel electronic part produces high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. An electrical component like this is included in the 16 series. Multiplexers built on a SPDT switching circuit are built. There are 3 circuits in this switch device. MC14053B can be used to search for analog multiplexer variants. It has an internal resistance of 280Ohm. The datasheets for the 16 pins explain the functions. This switch device is a typical Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 18V to the switch device in normal circumstances. Digital switch that provides Dual power at a cost-effective price. A low voltage of 3V should be applied to the electronic component. It would be sufficient to run this analogue multiplexer with 360nA current. A voltage of 3V~18V is required to drain this analog switch from a single voltage supply. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. In order to operate the 6 inputs, there are several steps to follow. This switch operates within the bandwidth of 17MHz.
MC14053BFELG Features
2 Channels
Switch Circuit: SPDT
360nA Supply Current
Bandwidth: 17MHz
MC14053BFELG Applications
There are a lot of ON Semiconductor MC14053BFELG Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Residential Gateways, Home Gateway/Router
- Modems
- PDAs
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Cellular phones
- Data Acquisition Systems
- Private Branch Exchange (PBX)
- Microprocessor controlled systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box