MC14551BDR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 280Ohm |
| Terminal Finish | Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 500mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 1.27mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | MC14551B |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Power Supplies | 5/15V |
| Number of Channels | 2 |
| Number of Circuits | 4 |
| Max Supply Voltage | 18V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 360nA |
| Power Dissipation | 500mW |
| Throw Configuration | DPST |
| Propagation Delay | 90 ns |
| Logic Function | Demultiplexer, Multiplexer |
| Number of Inputs | 8 |
| Halogen Free | Halogen Free |
| Supply Type | Dual |
| Bandwidth | 17MHz |
| On-State Resistance (Max) | 280Ohm |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 100nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF |
| On-state Resistance Match-Nom | 25Ohm |
| Switch Circuit | SPDT |
| Channel-to-Channel Matching (ΔRon) | 10 Ω |
| Voltage - Supply, Single (V+) | 3V~18V |
| Height Seated (Max) | 1.75mm |
| Length | 9.9mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC14551BDR2G Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SOIC (0.154, 3.90mm Width). High reliability is provided by advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 2:1 is the ratio between multiplexers and demultiplexers. Temperatures around -55°C~125°C TA are extended for operation. A total of 16 terminations have been recorded. By its 2 channels, the electronic component provides high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. There are 16 pins injected into the electronic part body. The analog switch ics are built using SPDT switching circuits. There are 4 circuits in this switch device. Try searching for the analog switch ic with MC14551B if you are looking for variants. A 280Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 16 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. Multiplexers should not be powered above 18V in normal situations. The analog switch ic is of the Dual supply type and is cost-effective. 3V is the lowest voltage the electrical component should receive. 360nA current would be enough for this multiplexer to operate. Using only a single voltage supply, this analog switch requires 3V~18V voltage. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board. There are SEPARATE OUTPUT outputs on this analog switch ic. It is possible to operate 8 inputs. 17MHz-bandwidths can be used to transfer data between multiplexers.
MC14551BDR2G Features
2 Channels
Switch Circuit: SPDT
360nA Supply Current
Bandwidth: 17MHz
MC14551BDR2G Applications
There are a lot of ON Semiconductor MC14551BDR2G Analog Switches & Multiplexers ICs applications.
- Imaging
- Microwave transmission systems
- SDH
- E1 Multiplexer
- High-Voltage
- Avionics test equipment
- Avionics
- HDTV
- ATM
- CSU
