MC33078DRE4
| Parameters | |
|---|---|
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Base Part Number | MC33078 |
| Pin Count | 8 |
| Number of Elements | 2 |
| Operating Supply Current | 2.05mA |
| Nominal Supply Current | 5mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 300nA |
| Voltage - Supply, Single/Dual (±) | 10V~36V ±5V~18V |
| Output Current per Channel | 37mA |
| Input Offset Voltage (Vos) | 2mV |
| Bandwidth | 16MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 16000 kHz |
| Voltage Gain | 110dB |
| Average Bias Current-Max (IIB) | 0.75μA |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Voltage - Input Offset | 150μV |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.75μA |
| Programmable Power | NO |
| Nominal Gain Bandwidth Product | 16MHz |
| Max I/O Voltage | 2mV |
| Power | NO |
| Input Offset Current-Max (IIO) | 0.15μA |
| Height | 1.75mm |
| Length | 4.9mm |
| Width | 3.91mm |
| Thickness | 1.58mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 8-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Weight | 72.603129mg |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | Operational Amplifier |
| Packing Method | TR |
| Technology | BIPOLAR |
MC33078DRE4 Overview
Packaged in a 8-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. An op amp ic of the General Purpose type. Upon delivery, op amp ic is packaged in a Tape & Reel (TR) case. During the past two weeks, there have been close to 8 terminations. A total of 8 pins are located on this board. It is important to remember that this op amp should be operated at a voltage of 15V volts. To be specific, this instrumentation amplifier is a type of Operational Amplifier. It has 8 pins that make up the linear amplifier. With regards to the offset voltage of the input, buffer amplifier is rated at 2mV. This electronic part is recommended for mounting type Surface Mount. It is recommended that this op amp ic be operated at a temperature no higher than -40°C~85°C for optimal performance. An 2.05mA volt supply current is needed for this linear amplifier to operate. It is recommended to keep the voltage gain at 110dB at all times. The buffer op amp is rated for an operating voltage of 2 when it comes to the power supply. To pack the operational amplifier ics, TR is adopted as the packing method.
MC33078DRE4 Features
8 Pins
supply voltage of 15V
110dB voltage gain
MC33078DRE4 Applications
There are a lot of Texas Instruments MC33078DRE4 Instrumentational OP Amps applications.
- Portable media players
- Instrumentation
- Scintillation detectors
- Fission chambers
- Band-pass filter
- High input resistance broadband
- Information processing
- Blood pressure sensors
- High-frequency data acquisition systems
- Multiplication circuits
