MC33079YDT
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 7 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.154, 3.90mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C |
| Packaging | Tape & Reel (TR) |
| Series | Automotive, AEC-Q100 |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Subcategory | Operational Amplifier |
| Packing Method | TAPE AND REEL; TUBE |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 1.27mm |
| Base Part Number | MC3307 |
| Pin Count | 14 |
| Power Supplies | +-2.5/+-15V |
| Number of Circuits | 4 |
| Operating Supply Current | 8mA |
| Supply Current-Max | 12mA |
| Slew Rate | 7V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | General Purpose |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 250nA |
| Voltage - Supply, Single/Dual (±) | 5V~30V ±2.5V~15V |
| Output Current per Channel | 37mA |
| Input Offset Voltage (Vos) | 2.5mV |
| Bandwidth | 15MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 9000 kHz |
| Voltage Gain | 100dB |
| Average Bias Current-Max (IIB) | 0.8μA |
| Power Supply Rejection Ratio (PSRR) | 105dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Supply Voltage Limit-Max | 18V |
| Low-Bias | NO |
| Micropower | NO |
| Bias Current-Max (IIB) @25C | 0.75μA |
| Programmable Power | NO |
| Neg Supply Voltage-Max (Vsup) | -18V |
| Input Offset Current-Max (IIO) | 0.175μA |
| Input Voltage Noise Density | 4.5nV/sqrt Hz |
| Height Seated (Max) | 1.75mm |
| Length | 8.65mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
MC33079YDT Overview
Packaged in a 14-SOIC (0.154, 3.90mm Width) case, the buffer op amp is ready to use. There are two types of operational amplifiers in this circuit. A Tape & Reel (TR) case is used to deliver the buffer op amp. The number of terminations is approaching the 14 mark. Linear amplifier has a total of 14 pins. Please take in mind that op amp should be run at 15V. There are two types of Operational Amplifier op amps in this case, and this device falls into one of them. There are 14 pins on this chip. Regarding input offset voltage, op amp rates 2.5mV. For this electrical component, the recommended mounting type is Surface Mount, which is the most common. In terms of operating temperature, this instrumentation amplifier performs well at a temperature of about -40°C~125°C . Using an 8mA supply current, this operational amplifier ics can be operated. 100dB should be the voltage gain. A instrumentation amplifier like this has 4 circuits. An buffer amplifier is packed in a TAPE AND REEL; TUBE-shape according to the design. In this case, Automotive, AEC-Q100 represents the instrumentation amplifiers' series number.
MC33079YDT Features
14 Pins
supply voltage of 15V
100dB voltage gain
MC33079YDT Applications
There are a lot of STMicroelectronics MC33079YDT Instrumentational OP Amps applications.
- Large motor controllers
- Gaming industry
- Inverse/same-phase proportional circuit
- Measurements of Wheatstone bridge
- Automotive sensors
- High input resistance broadband
- PDA
- Power generator
- Tablets
- Multiplication circuits
