MC33172P
| Parameters | |
|---|---|
| Lifecycle Status | LAST SHIPMENTS (Last Updated: 1 week ago) |
| Package / Case | PDIP |
| Surface Mount | NO |
| Number of Pins | 8 |
| Published | 2005 |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Subcategory | Operational Amplifier |
| Packing Method | RAIL |
| Technology | BIPOLAR |
| Terminal Position | DUAL |
| Terminal Form | THROUGH-HOLE |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 22V |
| Power Supplies | 5/+-15V |
| Temperature Grade | INDUSTRIAL |
| Number of Channels | 2 |
| Min Supply Voltage | 3V |
| Nominal Supply Current | 440μA |
| Max Supply Current | 500μA |
| Current - Output | 5mA |
| Slew Rate | 2.1 V/μs |
| Architecture | VOLTAGE-FEEDBACK |
| Amplifier Type | OPERATIONAL AMPLIFIER |
| Common Mode Rejection Ratio | 80 dB |
| Current - Input Bias | 100nA |
| Input Offset Voltage (Vos) | 5mV |
| Gain Bandwidth Product | 1.8MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Unity Gain BW-Nom | 1800 kHz |
| Voltage Gain | 113.98dB |
| Power Supply Rejection Ratio (PSRR) | 80dB |
| Low-Offset | NO |
| Frequency Compensation | YES |
| Max Dual Supply Voltage | 22V |
| Low-Bias | NO |
| Micropower | YES |
| Min Dual Supply Voltage | 1.5V |
| Bias Current-Max (IIB) @25C | 0.1μA |
| Programmable Power | NO |
| Dual Supply Voltage | 18V |
| Nominal Gain Bandwidth Product | 1.8MHz |
| Wideband | NO |
| Height | 3.44mm |
| Length | 10.16mm |
| Width | 6.6mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Contains Lead |
MC33172P Overview
In order to protect the op amps, a PDIP case is used. The instrumentation amplifier in this picture is of the OPERATIONAL AMPLIFIER-type. The number of terminations approaches 8. The pins on this board total to 8 in total. It would be helpful if you could remember that this op amp ic should be powered by an 15V battery. In more specific terms, this linear amplifier can be categoriOperational Amplifiered as a Operational Amplifier-type device. Linear amplifier includes 8 pins. As far as the input offset voltage is concerned, linear amplifier rates at 5mV. 113.98dB should be the voltage gain. As far as the device is concerned, buffer amplifier has 2 channels. Using this buffer op amp requires a temperature of at least -40°C. Use op amps only at temperatures no higher than 85°C. The operating supply voltage of instrumentation amplifier is rated 22V voltage. This linear amplifier pack is based on the RAIL axis. As a rule of thumb, the supply voltage of the op amp should not be lower than 3V. As a general rule, you should conduct this electronic component under dual supply voltages of 22V volts.
MC33172P Features
8 Pins
supply voltage of 15V
113.98dB voltage gain
MC33172P Applications
There are a lot of ON Semiconductor MC33172P Instrumentational OP Amps applications.
- Commercial audio systems
- Television
- Differentiator circuits
- High-frequency data acquisition systems
- Strain gauges
- Exponential operation circuits
- Laptop
- Switching amplifier
- Communication
- Addition operation circuits
