MC74AC273N
| Parameters | |
|---|---|
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AC273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 3.3/5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 175MHz |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 5.5 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 9ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height Seated (Max) | 4.57mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2009 |
| Series | 74AC |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
MC74AC273N Overview
In the form of 20-DIP (0.300, 7.62mm), it has been packaged. As part of the package Tube, it is embedded. T flip flop uses Non-Invertedas its output configuration. The trigger it is configured with uses Positive Edge. Through Holemounts this electrical part. Powered by a 2V~6Vvolt supply, it operates as follows. Temperature is set to -40°C~85°C TA. It belongs to the type D-Typeof flip flops. In this case, it is a type of FPGA belonging to the 74AC series. A frequency of 175MHzshould not be exceeded by its output. In total, it contains 1 elements. As a result, it consumes 8μA of quiescent current without being affected by external factors. The number of terminations is 20. Members of the 74AC273family make up this object. Power is provided by a 5V supply. Its input capacitance is 4.5pF farads. In terms of electronic devices, this device belongs to the ACfamily of devices. It is mounted in the way of Through Hole. As you can see from the design, it has pins with 20. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. It is included in FF/Latches. 8bits are used in its design. Vsup reaches 6V, the maximal supply voltage. Normally, the supply voltage (Vsup) should be above 2V. Its superior flexibility is attributed to its use of 8 circuits. Considering the reliability of this T flip flop, it is well suited for RAIL. It operates from 3.3/5V power supplies.
MC74AC273N Features
Tube package
74AC series
20 pins
8 Bits
3.3/5V power supplies
MC74AC273N Applications
There are a lot of ON Semiconductor MC74AC273N Flip Flops applications.
- Reduced system switching noise
- ESD performance
- ESD protection
- Guaranteed simultaneous switching noise level
- Divide a clock signal by 2 or 4
- Test & Measurement
- Control circuits
- Consumer
- QML qualified product
- Event Detectors
