MC74AC377DW
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 74AC |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74AC377 |
| Function | Standard |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 140MHz |
| Propagation Delay | 13 ns |
| Turn On Delay Time | 2 ns |
| Family | AC |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 75000000Hz |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74AC377DW Overview
20-SOIC (0.295, 7.50mm Width)is the packaging method. The package Tubecontains it. T flip flop uses Non-Invertedas its output configuration. The trigger configured with it uses Positive Edge. There is an electric part mounted in the way of Surface Mount. A supply voltage of 2V~6V is required for operation. A temperature of -40°C~85°C TAis considered to be the operating temperature. Logic flip flops of this type are classified as D-Type. This type of FPGA is a part of the 74AC series. A frequency of 140MHzshould not be exceeded by its output. A total of 1elements are present in it. It consumes 8μA of quiescent current without being affected by external factors. It has been determined that there have been 20 terminations. This D latch belongs to the family of 74AC377. The power supply voltage is 5V. JK flip flop input capacitance is 4.5pF farads. ACis the family of this D flip flop. There is an electronic part mounted in the way of Surface Mount. The electronic flip flop is designed with pins 20. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part you are looking for is included in FF/Latches. An electronic part with 8bits has been designed. The maximal supply voltage (Vsup) reaches 6V. For normal operation, the supply voltage (Vsup) should be above 2V. The superior flexibility of this product is achieved by using 8 circuits. High efficiency requires the supply voltage to be maintained at 5V.
MC74AC377DW Features
Tube package
74AC series
20 pins
8 Bits
MC74AC377DW Applications
There are a lot of ON Semiconductor MC74AC377DW Flip Flops applications.
- QML qualified product
- Set-reset capability
- Clock pulse
- Communications
- Balanced 24 mA output drivers
- Test & Measurement
- Circuit Design
- Frequency Divider circuits
- Shift registers
- Reduced system switching noise
