MC74AC74MELG
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 14-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74AC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74AC74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 2 |
| Load Capacitance | 50pF |
| Clock Frequency | 160MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 6 ns |
| Family | AC |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Number of Bits per Element | 1 |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Output Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC74AC74MELG Overview
It is embeded in 14-SOIC (0.209, 5.30mm Width) case. Package Tape & Reel (TR)embeds it. Differentialis the output configured for it. In the configuration of the trigger, Positive Edgeis used. This electronic part is mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~6V volts. Currently, the operating temperature is -40°C~85°C TA. This logic flip flop is classified as type D-Type. This type of FPGA is a part of the 74AC series. You should not exceed 160MHzin its output frequency. As a result, it consumes 4μA quiescent current and is not affected by external forces. There are 14 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. This D latch belongs to the family of 74AC74. The power supply voltage is 5V. This T flip flop has a capacitance of 4.5pF farads at the input. A device of this type belongs to the family of AC. There is an electronic component mounted in the way of Surface Mount. This board has 14 pins. This device has Positive Edgeas its clock edge trigger type. There is a FF/Latchesbase part number assigned to the RS flip flops. Vsup reaches 6V, the maximal supply voltage. Normally, the supply voltage (Vsup) should be kept above 2V. Its flexibility is enhanced by 2 circuits. As a result of its reliability, this D flip flop is ideally suited for TAPE AND REEL. There are 5V power supplies attached to it. Optimal efficiency requires a supply voltage of 5V. There are 1 output Lines, which generate the binary equivalent of the input line whose value is equal to “1” and are available to encode either a decimal or hexadecimal input pattern to typically a binary or “B. C. D” (binary coded decimal) output code.
MC74AC74MELG Features
Tape & Reel (TR) package
74AC series
14 pins
5V power supplies
MC74AC74MELG Applications
There are a lot of ON Semiconductor MC74AC74MELG Flip Flops applications.
- Latch-up performance
- Patented noise
- Single Down Count-Control Line
- Communications
- Computing
- Balanced 24 mA output drivers
- Pattern generators
- Load Control
- Supports Live Insertion
- Shift Registers
