MC74AC74N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| Series | 74AC |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74AC74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Operating Supply Voltage | 5V |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Load Capacitance | 50pF |
| Number of Bits | 1 |
| Clock Frequency | 160MHz |
| Propagation Delay | 14 ns |
| Turn On Delay Time | 6 ns |
| Family | AC |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Input Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 95000000Hz |
| Height Seated (Max) | 4.69mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74AC74N Overview
It is packaged in the way of 14-DIP (0.300, 7.62mm). The Tubepackage contains it. There is a Differentialoutput configured with it. JK flip flop uses Positive Edgeas the trigger. It is mounted in the way of Through Hole. Powered by a 2V~6Vvolt supply, it operates as follows. A temperature of -40°C~85°C TAis considered to be the operating temperature. It is an electronic flip flop with the type D-Type. In terms of FPGAs, it belongs to the 74AC series. You should not exceed 160MHzin the output frequency of the device. In total, it contains 2 elements. There is a consumption of 4μAof quiescent energy. There have been 14 terminations. This D latch belongs to the family of 74AC74. Power is provided by a 5V supply. A JK flip flop with a 4.5pFfarad input capacitance is used here. It is a member of the ACfamily of D flip flop. There is an electronic part mounted in the way of Through Hole. There are 14pins on it. In this device, the clock edge trigger type is Positive Edge. This device has the base part number FF/Latches. It is designed with a number of bits of 1. There is a 6Vmaximum supply voltage (Vsup). The supply voltage (Vsup) should be maintained above 2V for normal operation. In order to achieve high efficiency, the supply voltage should be maintained at 5V. This input has 1lines.
MC74AC74N Features
Tube package
74AC series
14 pins
1 Bits
MC74AC74N Applications
There are a lot of ON Semiconductor MC74AC74N Flip Flops applications.
- Bounce elimination switch
- Bus hold
- Reduced system switching noise
- Latch
- EMI reduction circuitry
- 2 – Bit synchronous counter
- Frequency Dividers
- Automotive
- Single Up Count-Control Line
- Synchronous counter
