MC74ACT273DTR2
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74ACT273 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 6.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Clock Edge Trigger Type | Positive Edge |
| Length | 6.5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
MC74ACT273DTR2 Overview
The flip flop is packaged in a case of 20-TSSOP (0.173, 4.40mm Width). There is an embedded version in the package Tape & Reel (TR). As configured, the output uses Non-Inverted. JK flip flop uses Positive Edgeas the trigger. There is an electrical part that is mounted in the way of Surface Mount. Powered by a 4.5V~5.5Vvolt supply, it operates as follows. It is operating at -40°C~85°C TA. This electronic flip flop is of type D-Type. JK flip flop belongs to the 74ACTseries of FPGAs. It should not exceed 200MHzin terms of its output frequency. In total, it contains 1 elements. This process consumes 8μA quiescents. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. The 74ACT273 family contains it. It is powered by a voltage of 5V . JK flip flop input capacitance is 4.5pF farads. An electronic device belonging to the family ACTcan be found here. Surface Mount mounts this electronic component. This board has 20 pins. This device has Positive Edgeas its clock edge trigger type. The part is included in FF/Latches. There are 8bits in this flip flop. The superior flexibility of this circuit is achieved by using 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The power supply is 5V. If high efficiency is desired, the supply voltage should be kept at 5V.
MC74ACT273DTR2 Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT273DTR2 Applications
There are a lot of ON Semiconductor MC74ACT273DTR2 Flip Flops applications.
- Guaranteed simultaneous switching noise level
- Buffer registers
- Count Modes
- Circuit Design
- Data Synchronizers
- Safety Clamp
- Bounce elimination switch
- Pattern generators
- ESD protection
- Instrumentation
