MC74ACT273N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2015 |
| Series | 74ACT |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 235 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Base Part Number | 74ACT273 |
| Function | Master Reset |
| Output Voltage | 6V |
| Output Type | Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 200MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 6.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 4.57mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74ACT273N Overview
The flip flop is packaged in 20-DIP (0.300, 7.62mm). A package named Tubeincludes it. As configured, the output uses Non-Inverted. This trigger uses the value Positive Edge. There is an electrical part that is mounted in the way of Through Hole. The supply voltage is set to 4.5V~5.5V. Currently, the operating temperature is -40°C~85°C TA. This electronic flip flop is of type D-Type. JK flip flop belongs to the 74ACTseries of FPGAs. It should not exceed 200MHzin its output frequency. In total, it contains 1 elements. T flip flop consumes 8μA quiescent energy. There are 20 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. It is a member of the 74ACT273 family. An input voltage of 5Vpowers the D latch. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Electronic devices of this type belong to the ACTfamily. The electronic part is mounted in the way of Through Hole. There are 20pins on it. A Positive Edgeclock edge trigger is used in this device. This part is included in FF/Latches. It is designed with a number of bits of 8. Due to its superior flexibility, it uses 8 circuits. A reliable performance of this D flip flop makes it well suited for use in RAIL. The D latch runs on a voltage of 5V volts. It is recommended that the supply voltage be kept at 5Vto maximize efficiency.
MC74ACT273N Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT273N Applications
There are a lot of ON Semiconductor MC74ACT273N Flip Flops applications.
- ESD performance
- High Performance Logic for test systems
- ESCC
- ATE
- Clock pulse
- Frequency division
- Shift registers
- Circuit Design
- Supports Live Insertion
- Frequency Divider circuits
