MC74ACT374MELG
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2006 |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74ACT374 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 160MHz |
| Propagation Delay | 10 ns |
| Turn On Delay Time | 8.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 90000000Hz |
| Height Seated (Max) | 2.05mm |
| Width | 5.275mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC74ACT374MELG Overview
As a result, it is packaged as 20-SOIC (0.209, 5.30mm Width). D flip flop is embedded in the Tape & Reel (TR) package. In the configuration, Tri-State, Non-Invertedis used as the output. This trigger is configured to use Positive Edge. There is an electric part mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 4.5V~5.5V volts. Currently, the operating temperature is -40°C~85°C TA. There is D-Type type of electronic flip flop associated with this device. The FPGA belongs to the 74ACT series. In order for it to function properly, its output frequency should not exceed 160MHz. The element count is 1 . As a result, it consumes 8μA quiescent current and is not affected by external forces. A total of 20terminations have been recorded. It is a member of the 74ACT374 family. It is powered from a supply voltage of 5V. The input capacitance of this T flip flop is 4.5pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. The electronic device belongs to the ACTfamily. There is an electronic component mounted in the way of Surface Mount. As you can see from the design, it has pins with 20. This device's clock edge trigger type is Positive Edge. There is a base part number FF/Latchesfor the RS flip flops. The design is based on 8bits. Due to its superior flexibility, it uses 8 circuits. On the basis of its reliable performance, this D flip flop is well suited for use with TAPE AND REEL. The system runs on a power supply of 5V watts. A total of 2ports are embedded in the D flip flop. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It is designed with 3 output lines.
MC74ACT374MELG Features
Tape & Reel (TR) package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT374MELG Applications
There are a lot of ON Semiconductor MC74ACT374MELG Flip Flops applications.
- Shift Registers
- Patented noise
- Safety Clamp
- ESCC
- Registers
- Divide a clock signal by 2 or 4
- Asynchronous counter
- Circuit Design
- Test & Measurement
- Dynamic threshold performance
