MC74ACT564NG
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 74ACT |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin (Sn) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74ACT564 |
| Function | Standard |
| Output Type | Tri-State, Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 85MHz |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 2 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 10.5ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 4.57mm |
| Width | 7.62mm |
| Radiation Hardening | No |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC74ACT564NG Overview
It is embeded in 20-DIP (0.300, 7.62mm) case. The package Tubecontains it. In the configuration, Tri-State, Invertedis used as the output. This trigger uses the value Positive Edge. In this case, the electronic component is mounted in the way of Through Hole. It operates with a supply voltage of 4.5V~5.5V. Currently, the operating temperature is -40°C~85°C TA. D-Typedescribes this flip flop. JK flip flop is a part of the 74ACTseries of FPGAs. It should not exceed 85MHzin its output frequency. A total of 1elements are contained within it. As a result, it consumes 8μA quiescent current. It has been determined that there have been 20 terminations. It is a member of the 74ACT564 family. It is powered from a supply voltage of 5V. This JK flip flop has a 4.5pFfarad input capacitance. This D flip flop belongs to the family of ACT. In this case, the electronic component is mounted in the way of Through Hole. 20pins are included in its design. This device has Positive Edgeas its clock edge trigger type. This device has the base part number FF/Latches. There are 8bits in its design. Its flexibility is enhanced by 8 circuits. The power supply is 5V. There are 2 ports embedded in the flip flops. If high efficiency is to be achieved, the supply voltage should be maintained at 5V. It has 3 output lines to operate.
MC74ACT564NG Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT564NG Applications
There are a lot of ON Semiconductor MC74ACT564NG Flip Flops applications.
- Count Modes
- QML qualified product
- Load Control
- Control circuits
- Synchronous counter
- Common Clocks
- Test & Measurement
- Safety Clamp
- Functionally equivalent to the MC10/100EL29
- Storage registers
