Parameters |
Factory Lead Time |
1 Week |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
20-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
20 |
Operating Temperature |
-40°C~85°C |
Packaging |
Tape & Reel (TR) |
Published |
2005 |
Series |
74ACT |
JESD-609 Code |
e4 |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
20 |
Terminal Finish |
Nickel/Palladium/Gold (Ni/Pd/Au) |
Subcategory |
FF/Latches |
Packing Method |
TAPE AND REEL |
Technology |
CMOS |
Voltage - Supply |
4.5V~5.5V |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
unknown |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
74ACT573 |
Pin Count |
20 |
Qualification Status |
Not Qualified |
Output Type |
Tri-State |
Operating Supply Voltage |
5V |
Circuit |
1:8 |
Polarity |
Non-Inverting |
Power Supplies |
5V |
Load Capacitance |
50pF |
Number of Ports |
2 |
Number of Bits |
8 |
Propagation Delay |
10.5 ns |
Turn On Delay Time |
10.5 ns |
Family |
ACT |
Logic Function |
Buffer, D-Type, Latch |
Current - Output High, Low |
24mA 24mA |
Logic Type |
D-Type Transparent Latch |
Max I(ol) |
0.024 A |
Number of Input Lines |
8 |
Independent Circuits |
1 |
Number of Output Lines |
3 |
Length |
6.5mm |
Width |
4.4mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
MC74ACT573DTR2 Overview
In the 20-TSSOP (0.173, 4.40mm Width) package, it can be found as an embedded module. Tape & Reel (TR) is the packaging method. Tri-State is the output configured for it. A D-Type Transparent Latch logic type is used in this electrical device. Mounting this electronic component follows the Surface Mount method. There is no supply voltage for this device. It is -40°C~85°C at the operating temperature. It is a type of FPGA belonging to the 74ACT series. It is designed with 8 bits. A device such as this has 20 terminations designed. As a member of the 74ACT573 family, it falls under that category. A 5V voltage supply is required for operation. With 20 pins, it is equipped. This electronic device belongs to the family of ACT. The 20 pins are designed into it. Electronic parts are mounted using the Surface Mount method. This device has 2 ports on board, which are all available at the same time. It belongs to the subcategory of FF/Latches. A total of 5V power supplies are needed to run it. An electronic circuit can be found on 8 input lines. This device is well suited for TAPE AND REEL based on its reliable performance. A high level of efficiency is achieved by maintaining the supply voltage at 5V. 3 output lines provide binary equivalents of input lines.
MC74ACT573DTR2 Features
20-TSSOP (0.173, 4.40mm Width) package
74ACT series
8 Bits
74ACT573 family
20 pin count
20 pins
5V power supplies
MC74ACT573DTR2 Applications
There are a lot of ON Semiconductor MC74ACT573DTR2 Latches applications.
- General-Purpose Register
- Pattern Generators
- Shift left with parallel loading
- Buffer Storage
- Watches
- Up-Down Johnson
- Automotive Infotainment
- Up/down difference counting
- Lamp and Display (LED)
- Buffer register