MC74ACT573DWR2
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.295, 7.50mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Series | 74ACT |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74ACT573 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Output Type | Tri-State |
| Circuit | 1:8 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Propagation Delay | 10.5 ns |
| Turn On Delay Time | 10.5 ns |
| Family | ACT |
| Logic Function | Buffer, D-Type, Latch |
| Current - Output High, Low | 24mA 24mA |
| Logic Type | D-Type Transparent Latch |
| Max I(ol) | 0.024 A |
| Independent Circuits | 1 |
| Number of Output Lines | 3 |
| Height Seated (Max) | 2.65mm |
| Width | 7.5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74ACT573DWR2 Overview
In the 20-SOIC (0.295, 7.50mm Width) package, it can be found as an embedded module. A Tape & Reel (TR) package is used to package it. The output it is configured with uses Tri-State. In this electrical device, the logic type is D-Type Transparent Latch. Mounting this electronic component follows the Surface Mount method. With a supply voltage of 4.5V~5.5V, it operates. It operates at -40°C~85°C degrees Celsius. The 74ACT series is associated with this FPGA. The electronic part in this image has 8 bits. A device with this design has 20 terminations. The family it belongs to is 74ACT573. In order to function, the supply voltage should be set to 5V. The 20 pind are equipped with it. It is part of the family of electronic devices called ACT. Designed with 20 pins, it is compatible with a wide range of devices. Surface Mount is the method used for mounting this electronic part. This device is equipped with 2 ports. There is a subcategory of FF/Latches for this part. It is possible to reach 5.5V when the maximum supply voltage (Vsup) has been reached. 5V power supplies are needed to operate it. It is recommended to have a higher supply voltage (Vsup) than 4.5V. As a result of its reliable performance, it is well suited for TAPE AND REEL. Regardless of the input line, the binary equivalent of the input line will be generated by the 3 output lines. Its superior flexibility is achieved by using 8 circuits.
MC74ACT573DWR2 Features
20-SOIC (0.295, 7.50mm Width) package
74ACT series
8 Bits
74ACT573 family
20 pin count
20 pins
5V power supplies
MC74ACT573DWR2 Applications
There are a lot of ON Semiconductor MC74ACT573DWR2 Latches applications.
- Sample and hold register
- Automatic test equipment
- Meter applications
- Parallel-to-Serial Data Conversion
- Address register
- Data acquisition
- Motor Drives
- PCs and Notebooks
- Phase comparator
- Clocks
