MC74ACT574MG
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 74ACT |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.05mm |
| Width | 5.275mm |
| RoHS Status | RoHS Compliant |
| Lead Free | Lead Free |
MC74ACT574MG Overview
As a result, it is packaged as 20-SOIC (0.209, 5.30mm Width). D flip flop is embedded in the Tube package. Currently, the output is configured to use Tri-State, Non-Inverted. The trigger it is configured with uses Positive Edge. Surface Mountis occupied by this electronic component. The supply voltage is set to 4.5V~5.5V. It is operating at a temperature of -40°C~85°C TA. D-Typeis the type of this D latch. It belongs to the 74ACTseries of FPGAs. A frequency of 100MHzshould not be exceeded by its output. In total, it contains 1 elements. This process consumes 8μA quiescents. It has been determined that there have been 20 terminations. This D latch belongs to the family of 74ACT574. Power is provided by a 5V supply. A JK flip flop with a 4.5pFfarad input capacitance is used here. Devices in the ACTfamily are electronic devices. There is an electronic component mounted in the way of Surface Mount. The 20pins are designed into the board. There is a clock edge trigger type of Positive Edgeon this device. The RS flip flops belongs to FF/Latches base part number. There are 8bits in this flip flop. Its flexibility is enhanced by 8 circuits. There are 5V power supplies attached to it. A total of 2ports are embedded in the D flip flop. A high level of efficiency can be achieved by maintaining the supply voltage at 5V. In order to operate, the chip has 3 output lines.
MC74ACT574MG Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT574MG Applications
There are a lot of ON Semiconductor MC74ACT574MG Flip Flops applications.
- Shift registers
- Storage Registers
- Set-reset capability
- ATE
- Cold spare funcion
- ESCC
- Event Detectors
- Latch-up performance
- CMOS Process
- Load Control
