MC74ACT574N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 20-DIP (0.300, 7.62mm) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2006 |
| Series | 74ACT |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | 240 |
| Supply Voltage | 5V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | 74ACT574 |
| Function | Standard |
| Qualification Status | Not Qualified |
| Output Type | Tri-State, Non-Inverted |
| Operating Supply Voltage | 5V |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Power Supplies | 5V |
| Load Capacitance | 50pF |
| Number of Ports | 2 |
| Number of Bits | 8 |
| Clock Frequency | 100MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 2.5 ns |
| Family | ACT |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 8μA |
| Current - Output High, Low | 24mA 24mA |
| Max I(ol) | 0.024 A |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Input Lines | 8 |
| Number of Output Lines | 3 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 4.57mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74ACT574N Overview
The item is packaged in 20-DIP (0.300, 7.62mm)cases. D flip flop is embedded in the Tube package. Tri-State, Non-Invertedis the output configured for it. It is configured with a trigger that uses a value of Positive Edge. There is an electronic component mounted in the way of Through Hole. The supply voltage is set to 4.5V~5.5V. It is operating at -40°C~85°C TA. This D latch has the type D-Type. JK flip flop belongs to the 74ACTseries of FPGAs. Its output frequency should not exceed 100MHz. In total, it contains 1 elements. As a result, it consumes 8μA of quiescent current without being affected by external factors. There are 20 terminations,JK flip flop belongs to 74ACT574 family. A voltage of 5V provides power to the D latch. Input capacitance of this device is 4.5pF farads. The electronic device belongs to the ACTfamily. There is an electronic part that is mounted in the way of Through Hole. A total of 20pins are provided on this board. This device's clock edge trigger type is Positive Edge. This device has the base part number FF/Latches. There are 8bits in its design. The system runs on a power supply of 5V watts. The D flip flop is embedded with 2ports. For high efficiency, the supply voltage should be kept at 5V. There are no output lines on the JK flip flop. It is reported that there are 8 input lines.
MC74ACT574N Features
Tube package
74ACT series
20 pins
8 Bits
5V power supplies
MC74ACT574N Applications
There are a lot of ON Semiconductor MC74ACT574N Flip Flops applications.
- Buffered Clock
- Functionally equivalent to the MC10/100EL29
- Latch-up performance
- Latch
- Patented noise
- Bounce elimination switch
- Consumer
- Data transfer
- Storage Registers
- Reduced system switching noise
