MC74ACT74N
| Parameters | |
|---|---|
| Mount | Through Hole |
| Mounting Type | Through Hole |
| Package / Case | 14-DIP (0.300, 7.62mm) |
| Number of Pins | 14 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| Published | 2001 |
| Series | 74ACT |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| Type | D-Type |
| Terminal Finish | Tin/Lead (Sn/Pb) |
| Subcategory | FF/Latches |
| Technology | CMOS |
| Voltage - Supply | 4.5V~5.5V |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Supply Voltage | 5V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | 74ACT74 |
| Function | Set(Preset) and Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 2 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 5.5V |
| Power Supplies | 5V |
| Supply Voltage-Min (Vsup) | 4.5V |
| Load Capacitance | 50pF |
| Number of Bits | 1 |
| Clock Frequency | 210MHz |
| Propagation Delay | 11 ns |
| Turn On Delay Time | 5.5 ns |
| Family | ACT |
| Logic Function | AND, D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 24mA 24mA |
| Max Propagation Delay @ V, Max CL | 11ns @ 5V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 4.5pF |
| Number of Input Lines | 1 |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 4.69mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74ACT74N Overview
The package is in the form of 14-DIP (0.300, 7.62mm). D flip flop is included in the Tubepackage. T flip flop uses Differentialas the output. This trigger uses the value Positive Edge. Through Holemounts this electrical part. A supply voltage of 4.5V~5.5V is required for operation. Temperature is set to -40°C~85°C TA. Logic flip flops of this type are classified as D-Type. JK flip flop belongs to the 74ACTseries of FPGAs. A frequency of 210MHzshould not be exceeded by its output. D latch consists of 2 elements. During its operation, it consumes 4μA quiescent energy. The number of terminations is 14. It is a member of the 74ACT74 family. A voltage of 5V is used as the power supply for this D latch. This T flip flop has a capacitance of 4.5pF farads at the input. An electronic device belonging to the family ACTcan be found here. Through Hole mounts this electronic component. Basically, it is designed with a set of 14 pins. A Positive Edgeclock edge trigger is used in this device. This part is included in FF/Latches. An electronic part designed with 1bits is used in this application. There is a 5.5Vmaximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be kept above 4.5V. It runs on 5Vvolts of power. This input has 1lines.
MC74ACT74N Features
Tube package
74ACT series
14 pins
1 Bits
5V power supplies
MC74ACT74N Applications
There are a lot of ON Semiconductor MC74ACT74N Flip Flops applications.
- Memory
- Storage Registers
- Differential Individual
- Pattern generators
- Frequency Divider circuits
- Single Up Count-Control Line
- Computing
- Shift registers
- Buffered Clock
- Matched Rise and Fall
