MC74HC174ADTR2G
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 3 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2005 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC174 |
| Function | Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 6 |
| Number of Circuits | 7 |
| Load Capacitance | 50pF |
| Number of Bits | 6 |
| Clock Frequency | 35MHz |
| Propagation Delay | 110 ns |
| Turn On Delay Time | 24 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max I(ol) | 0.004 A |
| Max Propagation Delay @ V, Max CL | 19ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 20000000Hz |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74HC174ADTR2G Overview
The flip flop is packaged in 16-TSSOP (0.173, 4.40mm Width). Package Tape & Reel (TR)embeds it. This output is configured with Non-Inverted. This trigger uses the value Positive Edge. There is an electronic component mounted in the way of Surface Mount. The JK flip flop operates with an input voltage of 2V~6V volts. In the operating environment, the temperature is -55°C~125°C TA. A flip flop of this type is classified as a D-Type. In FPGA terms, D flip flop is a type of 74HCseries FPGA. You should not exceed 35MHzin the output frequency of the device. A total of 1elements are present in it. As a result, it consumes 4μA quiescent current. There are 16 terminations, which are the practice of ending a transmission line with a device that matches the characteristic impedance of the line. JK flip flop belongs to 74HC174 family. It is powered from a supply voltage of 5V. The input capacitance of this JK flip flopis 10pF farads. A device of this type belongs to the family of HC/UH. In this case, the electronic component is mounted in the way of Surface Mount. This board is designed with 16pins on it. This device exhibits a clock edge trigger type of Positive Edge. There is a FF/Latchesbase part number assigned to the RS flip flops. There are 6bits in this flip flop. There is a 6Vmaximum supply voltage (Vsup). Normally, the supply voltage (Vsup) should be above 2V. The superior flexibility is achieved through the use of 7 circuits. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. It is of 6 channels.
MC74HC174ADTR2G Features
Tape & Reel (TR) package
74HC series
16 pins
6 Bits
MC74HC174ADTR2G Applications
There are a lot of ON Semiconductor MC74HC174ADTR2G Flip Flops applications.
- Divide a clock signal by 2 or 4
- Control circuits
- Cold spare funcion
- Registers
- 2 – Bit synchronous counter
- EMI reduction circuitry
- Matched Rise and Fall
- ESCC
- Asynchronous counter
- Single Up Count-Control Line
