MC74HC175ADTR2
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC175 |
| Function | Master Reset |
| Qualification Status | Not Qualified |
| Output Type | Differential |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 4 |
| Load Capacitance | 50pF |
| Number of Bits | 4 |
| Clock Frequency | 35MHz |
| Propagation Delay | 150 ns |
| Turn On Delay Time | 28 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 5.2mA 5.2mA |
| Max Propagation Delay @ V, Max CL | 22ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Clock Edge Trigger Type | Positive Edge |
| Max Frequency@Nom-Sup | 20000000Hz |
| Length | 5mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74HC175ADTR2 Overview
The flip flop is packaged in a case of 16-TSSOP (0.173, 4.40mm Width). D flip flop is included in the Tape & Reel (TR)package. This output is configured with Differential. It is configured with a trigger that uses Positive Edge. The electronic part is mounted in the way of Surface Mount. The JK flip flop operates at a voltage of 2V~6V. A temperature of -55°C~125°C TAis used in the operation. D-Typedescribes this flip flop. The FPGA belongs to the 74HC series. You should not exceed 35MHzin its output frequency. A total of 1 elements are present. As a result, it consumes 4μA quiescent current. A total of 16 terminations have been made. It is a member of the 74HC175 family. A voltage of 3V is used to power it. There is 10pF input capacitance for this T flip flop. This D flip flop belongs to the family of HC/UH. There is an electronic part that is mounted in the way of Surface Mount. 16pins are included in its design. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. This part is included in FF/Latches. This flip flop is designed with 4 Bits. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be above 2V. Its superior flexibility is attributed to its use of 4 circuits. In light of its reliable performance, this T flip flop is well suited for TAPE AND REEL. It runs on 2/6Vvolts of power.
MC74HC175ADTR2 Features
Tape & Reel (TR) package
74HC series
16 pins
4 Bits
2/6V power supplies
MC74HC175ADTR2 Applications
There are a lot of ON Semiconductor MC74HC175ADTR2 Flip Flops applications.
- Memory
- Matched Rise and Fall
- 2 – Bit synchronous counter
- Differential Individual
- Circuit Design
- Reduced system switching noise
- Cold spare funcion
- Power down protection
- EMI reduction circuitry
- Guaranteed simultaneous switching noise level
