MC74HC273ADTG
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | ACTIVE (Last Updated: 2 days ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| Published | 2005 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Pbfree Code | yes |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | RAIL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC273 |
| Function | Reset |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Channels | 8 |
| Load Capacitance | 50pF |
| Output Current | 7.8mA |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 220 ns |
| Turn On Delay Time | 25 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Halogen Free | Halogen Free |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 25ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| Number of Output Lines | 8 |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height | 1.05mm |
| Length | 6.6mm |
| Width | 4.5mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
MC74HC273ADTG Overview
As a result, it is packaged as 20-TSSOP (0.173, 4.40mm Width). D flip flop is embedded in the Tube package. In the configuration, Non-Invertedis used as the output. It is configured with the trigger Positive Edge. There is an electronic component mounted in the way of Surface Mount. Powered by a 2V~6Vvolt supply, it operates as follows. Currently, the operating temperature is -55°C~125°C TA. This electronic flip flop is of type D-Type. FPGAs belonging to the 74HCseries contain this type of chip. You should not exceed 35MHzin the output frequency of the device. In total, there are 1 elements. It consumes 4μA of quiescent current without being affected by external factors. The number of terminations is 20. The 74HC273 family contains it. Power is provided by a 3V supply. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. An electronic device belonging to the family HC/UHcan be found here. It is mounted by the way of Surface Mount. It is designed with 20 pins. Edge triggering is a type of triggering that allows a circuit to become active at the positive edge or the negative edge of the clock signal. The clock edge trigger type of this device is Positive Edge. The part you are looking for is included in FF/Latches. There are 8bits in its design. It reaches 6Vwhen the maximum supply voltage (Vsup) is applied. Normally, the supply voltage (Vsup) should be kept above 2V. As a result of its reliability, this D flip flop is ideally suited for RAIL. The system runs on a power supply of 2/6V watts. Featuring the maximum design flexibility, it has an output current of 7.8mA . It has 8 output lines to operate. There are 8 channels available.
MC74HC273ADTG Features
Tube package
74HC series
20 pins
8 Bits
2/6V power supplies
MC74HC273ADTG Applications
There are a lot of ON Semiconductor MC74HC273ADTG Flip Flops applications.
- Computers
- Divide a clock signal by 2 or 4
- Storage registers
- QML qualified product
- Event Detectors
- Functionally equivalent to the MC10/100EL29
- Single Down Count-Control Line
- Pattern generators
- Guaranteed simultaneous switching noise level
- Dynamic threshold performance
