MC74HC273AFEL
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-SOIC (0.209, 5.30mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Published | 2011 |
| Series | 74HC |
| JESD-609 Code | e4 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| Type | D-Type |
| Terminal Finish | Nickel/Palladium/Gold (Ni/Pd/Au) |
| Subcategory | FF/Latches |
| Packing Method | TAPE AND REEL |
| Technology | CMOS |
| Voltage - Supply | 2V~6V |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | 74HC273 |
| Function | Reset |
| Qualification Status | Not Qualified |
| Output Type | Non-Inverted |
| Number of Elements | 1 |
| Polarity | Non-Inverting |
| Supply Voltage-Max (Vsup) | 6V |
| Power Supplies | 2/6V |
| Supply Voltage-Min (Vsup) | 2V |
| Number of Circuits | 8 |
| Load Capacitance | 50pF |
| Number of Bits | 8 |
| Clock Frequency | 35MHz |
| Propagation Delay | 145 ns |
| Turn On Delay Time | 25 ns |
| Family | HC/UH |
| Logic Function | D-Type, Flip-Flop |
| Current - Quiescent (Iq) | 4μA |
| Current - Output High, Low | 7.8mA 7.8mA |
| Max I(ol) | 0.006 A |
| Max Propagation Delay @ V, Max CL | 25ns @ 6V, 50pF |
| Trigger Type | Positive Edge |
| Input Capacitance | 10pF |
| fmax-Min | 24 MHz |
| Clock Edge Trigger Type | Positive Edge |
| Height Seated (Max) | 2.05mm |
| Width | 5.275mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
MC74HC273AFEL Overview
20-SOIC (0.209, 5.30mm Width)is the packaging method. The Tape & Reel (TR)package contains it. Non-Invertedis the output configured for it. JK flip flop uses Positive Edgeas the trigger. There is an electronic component mounted in the way of Surface Mount. A voltage of 2V~6Vis required for its operation. The operating temperature is -55°C~125°C TA. Logic flip flops of this type are classified as D-Type. In FPGA terms, D flip flop is a type of 74HCseries FPGA. You should not exceed 35MHzin its output frequency. In total, it contains 1 elements. During its operation, it consumes 4μA quiescent energy. A total of 20terminations have been recorded. It is a member of the 74HC273 family. A voltage of 3V is used to power it. The input capacitance of this T flip flop is 10pF farads, which is defined as the capacitance between the input terminals of an op amp with either input grounded. Devices in the HC/UHfamily are electronic devices. The electronic part is mounted in the way of Surface Mount. It is designed with 20 pins. This device exhibits a clock edge trigger type of Positive Edge. The part is included in FF/Latches. There are 8bits in its design. It reaches 6Vwhen the supply voltage is maximal (Vsup). A normal operating voltage (Vsup) should remain above 2V. Its superior flexibility is attributed to its use of 8 circuits. This D flip flop is well suited for TAPE AND REEL based on its reliable performance. A total of 2/6V power supplies are needed to run it.
MC74HC273AFEL Features
Tape & Reel (TR) package
74HC series
20 pins
8 Bits
2/6V power supplies
MC74HC273AFEL Applications
There are a lot of ON Semiconductor MC74HC273AFEL Flip Flops applications.
- Cold spare funcion
- QML qualified product
- Balanced 24 mA output drivers
- Single Up Count-Control Line
- Latch
- Patented noise
- Data transfer
- CMOS Process
- Communications
- ESCC
